Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

47-1230 Refinishing
#25

Warren, 30 psi sounds about right. If you were using less than 50/50, drop it down to at least that level. Depending on temperature I might go as low as 30/70. Play with a bit on some scrap wood. I believe that the reduction they suggest is for brushing, not spraying. The higher the ratio of thinner to lacquer, the smoother it will go on. Doesn't put a lot of lacquer on but it can be built up with multiple coats. Again, try to spray on with the surface flat. More care is required on spraying on vertical surfaces. I hate runs.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.


Messages In This Thread
47-1230 Refinishing - by Warren - 06-22-2013, 11:36 PM
RE: 47-1230 Refinishing - by klondike98 - 06-23-2013, 10:45 AM
RE: 47-1230 Refinishing - by Arran - 06-23-2013, 09:08 PM
RE: 47-1230 Refinishing - by Warren - 06-24-2013, 12:49 PM
RE: 47-1230 Refinishing - by Marsupial - 06-27-2013, 03:07 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 06-27-2013, 11:44 PM
RE: 47-1230 Refinishing - by Arran - 06-28-2013, 02:17 AM
RE: 47-1230 Refinishing - by Warren - 06-28-2013, 02:27 PM
RE: 47-1230 Refinishing - by Steve Davis - 06-28-2013, 03:43 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 06-28-2013, 05:02 PM
RE: 47-1230 Refinishing - by Warren - 06-28-2013, 09:07 PM
RE: 47-1230 Refinishing - by Warren - 07-18-2013, 02:26 PM
RE: 47-1230 Refinishing - by Bob Andersen - 07-18-2013, 05:20 PM
RE: 47-1230 Refinishing - by Warren - 07-18-2013, 08:44 PM
RE: 47-1230 Refinishing - by Warren - 07-30-2013, 12:55 AM
RE: 47-1230 Refinishing - by Arran - 07-30-2013, 10:39 AM
RE: 47-1230 Refinishing - by jerryhawthorne - 07-30-2013, 01:47 PM
RE: 47-1230 Refinishing - by Warren - 07-31-2013, 12:01 AM
RE: 47-1230 Refinishing - by jerryhawthorne - 07-31-2013, 12:11 AM
RE: 47-1230 Refinishing - by Warren - 08-03-2013, 11:45 PM
RE: 47-1230 Refinishing - by Warren - 10-13-2013, 10:58 PM
RE: 47-1230 Refinishing - by Warren - 12-13-2013, 07:31 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 12-13-2013, 08:00 PM
RE: 47-1230 Refinishing - by Warren - 12-14-2013, 04:16 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 12-14-2013, 05:22 PM
RE: 47-1230 Refinishing - by Warren - 12-15-2013, 02:17 AM



Users browsing this thread: 10 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>