1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
40-201 Dial Lamp Socket Rebuild
bfrohwein
Member
***
Posts: 152
Threads: 11
Joined: Feb 2013
City: Dallas, TX
#10

12-16-2013, 09:42 PM
look at my thread on the 41-315X (not the alignment one). I just posted two pics of the jewel I installed. it looks remarkably like the original. assuming yours also has the 3/8" hole. the original plastic ones, from what I've read in several places, dried out, deformed and crumbled to dust. Which is why they're missing 99% of the time.

anyhow.. I have 3 more of those, I can bring one to the next VRPS meeting. You just need to pop the neon guts out of it, possibly trim off 1/8-1/4" and it pops right in, nice and snug.
Find
« Next Oldest | Next Newest »


Messages In This Thread
40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-02-2013, 09:05 PM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-05-2013, 07:39 AM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-16-2013, 07:30 AM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-16-2013, 06:07 PM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-16-2013, 07:53 PM
RE: 40-201 Dial Lamp Socket Rebuild - by bfrohwein - 12-16-2013, 09:42 PM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-17-2013, 07:46 AM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-19-2013, 11:25 AM
RE: 40-201 Dial Lamp Socket Rebuild - by Joeztech - 12-19-2013, 06:11 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 5455 online users. [Complete List]
» 4 Member(s) | 5451 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration