40-201 now has power

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

40-201 now has power

BrendaAnnD
Phorum Expert

Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington

#19

12-25-2013, 06:47 PM

If you still have any old caps in there, you really should replace them before powering the set up again. That tone control should be your ultimate clue that all the caps are bad. This is likely what is causing your start-up crackling. This could also be caused by a noisy resistor.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

40-201 now has power - by Joeztech - 12-23-2013, 03:45 PM

RE: 40-201 now has power - by jerryhawthorne - 12-23-2013, 04:27 PM

RE: 40-201 now has power - by Joeztech - 12-23-2013, 06:45 PM

RE: 40-201 now has power - by jerryhawthorne - 12-23-2013, 07:13 PM

RE: 40-201 now has power - by Joeztech - 12-23-2013, 08:08 PM

RE: 40-201 now has power - by codefox1 - 12-23-2013, 08:56 PM

RE: 40-201 now has power - by jontz - 12-23-2013, 09:33 PM

RE: 40-201 now has power - by Paul Philco322 - 12-23-2013, 11:11 PM

RE: 40-201 now has power - by Joeztech - 12-24-2013, 07:33 AM

RE: 40-201 now has power - by Joeztech - 12-24-2013, 07:45 AM

RE: 40-201 now has power - by hsusmann - 12-24-2013, 10:14 AM

RE: 40-201 now has power - by Joeztech - 12-24-2013, 04:53 PM

RE: 40-201 now has power - by hsusmann - 12-24-2013, 05:53 PM

RE: 40-201 now has power - by Joeztech - 12-24-2013, 08:03 PM

RE: 40-201 now has power - by hsusmann - 12-24-2013, 08:53 PM

RE: 40-201 now has power - by Joeztech - 12-24-2013, 10:54 PM

RE: 40-201 now has power - by Radioroslyn - 12-25-2013, 11:15 AM

RE: 40-201 now has power - by Joeztech - 12-25-2013, 03:34 PM

RE: 40-201 now has power - by BrendaAnnD - 12-25-2013, 06:47 PM

RE: 40-201 now has power - by Joeztech - 12-25-2013, 07:05 PM

RE: 40-201 now has power - by Joeztech - 12-26-2013, 08:15 AM

RE: 40-201 now has power - by hsusmann - 12-26-2013, 09:53 AM

RE: 40-201 now has power - by Joeztech - 12-26-2013, 11:48 AM

RE: 40-201 now has power - by hsusmann - 12-26-2013, 10:54 PM

RE: 40-201 now has power - by BrendaAnnD - 12-26-2013, 11:59 PM

RE: 40-201 now has power - by Eric Adams - 12-27-2013, 01:50 AM

RE: 40-201 now has power - by Joeztech - 12-27-2013, 07:28 AM

RE: 40-201 now has power - by Joeztech - 12-28-2013, 01:28 PM

RE: 40-201 now has power - by Joeztech - 12-28-2013, 05:36 PM

RE: 40-201 now has power - by codefox1 - 12-29-2013, 08:30 PM

RE: 40-201 now has power - by morzh - 12-29-2013, 08:42 PM

RE: 40-201 now has power - by Joeztech - 12-30-2013, 07:17 AM

RE: 40-201 now has power - by Joeztech - 12-30-2013, 07:30 AM

RE: 40-201 now has power - by Joeztech - 12-31-2013, 06:33 PM

RE: 40-201 now has power - by jerryhawthorne - 12-31-2013, 07:54 PM

RE: 40-201 now has power - by Joeztech - 02-19-2014, 08:05 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
The 2 towns you mentioned "Frustrated" and "Give Up" are places we have all been. Relax, take 5, thi...Paul Philco322 — 03:23 PM
Philco 89 Code 123 Osc Coil
Thanks for posting that information!klondike98 — 03:14 PM
Philco 42-345 Restoration/Repair
From what I see is the blue cap was added by someone after the radio was sold presumably to replace cap 40A. I can't tel...RodB — 03:12 PM
Philco 42-345 Restoration/Repair
Correction My original picture shows #40 cap, blue cap and #42 resistor connected.osanders0311 — 02:23 PM
Philco 42-345 Restoration/Repair
Well guys I am stuck, frustrated and about ready to give up. For starters all I'm getting from the speaker is a humming ...osanders0311 — 02:17 PM
[split] New member...
Thanks. I'll try that.HowardWoodard — 01:13 PM
[split] New member...
You may have to start further back with your signal injection at the IF signal grid, then tune the second IF transformer...RodB — 10:28 AM
[split] New member...
Well, with the replacement tuning assembly, I have finally put the unit back together and aligned the dial. The first s...HowardWoodard — 01:01 AM
Philco Model 16 wiring question
Well, finding a short is easy. Like I said, disconnect the transformer's secondary windings and see if it persists. If...morzh — 09:48 PM
Restoring Philco 96
Nice one!Stan the Man — 09:37 PM

Who's Online

There are currently 1040 online users. [Complete List]
» 3 Member(s) | 1037 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me