Philco 41-315X

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 41-315X

jeffgniffke
Junior Member

Posts: 46
Threads: 7
Joined: Apr 2013
City: Grand Marais, MN 55604

#23

12-26-2013, 07:06 PM

I have focused on the chassis on these guys but they were beautiful cabinets in there time...but the escutcheons are the weak link for sure...i actually used now of the painted faux brass ones I had in parts in good shape to replace a badly faded one on a 41-295.
That is good info Bret thank you....
The one I would like to do this to with some solid effort is the 42-1015 i have. A high end set with Beam of Light etc

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 41-315X - by bfrohwein - 11-08-2013, 01:35 AM

RE: Philco 41-315X - by Bill Kinghorn - 11-08-2013, 01:08 PM

RE: Philco 41-315X - by bfrohwein - 11-08-2013, 02:06 PM

RE: Philco 41-315X - by Ron Ramirez - 11-08-2013, 06:08 PM

RE: Philco 41-315X - by bfrohwein - 11-08-2013, 07:23 PM

RE: Philco 41-315X - by Bill Kinghorn - 11-09-2013, 03:41 PM

RE: Philco 41-315X - by bfrohwein - 11-09-2013, 07:00 PM

RE: Philco 41-315X - by Arran - 11-09-2013, 11:14 PM

RE: Philco 41-315X - by bfrohwein - 12-08-2013, 11:56 PM

RE: Philco 41-315X - by Ron Ramirez - 12-10-2013, 06:11 PM

RE: Philco 41-315X - by bfrohwein - 12-10-2013, 09:34 PM

RE: Philco 41-315X - by bfrohwein - 12-16-2013, 07:02 PM

RE: Philco 41-315X - by jeffgniffke - 12-22-2013, 03:53 PM

RE: Philco 41-315X - by bfrohwein - 12-22-2013, 06:56 PM

RE: Philco 41-315X - by jeffgniffke - 12-23-2013, 04:53 PM

RE: Philco 41-315X - by Ron Ramirez - 12-23-2013, 05:29 PM

RE: Philco 41-315X - by bfrohwein - 12-24-2013, 02:43 PM

RE: Philco 41-315X - by Joeztech - 12-25-2013, 10:46 AM

RE: Philco 41-315X - by bfrohwein - 12-25-2013, 12:46 PM

RE: Philco 41-315X - by Ron Ramirez - 12-25-2013, 12:48 PM

RE: Philco 41-315X - by jeffgniffke - 12-26-2013, 05:49 PM

RE: Philco 41-315X - by bfrohwein - 12-26-2013, 06:59 PM

RE: Philco 41-315X - by jeffgniffke - 12-26-2013, 07:06 PM

RE: Philco 41-315X - by bfrohwein - 01-01-2014, 03:59 PM

RE: Philco 41-315X - by jeffgniffke - 01-01-2014, 09:14 PM

RE: Philco 41-315X - by jeffgniffke - 01-01-2014, 09:19 PM

RE: Philco 41-315X - by jeffgniffke - 01-10-2014, 01:08 PM

RE: Philco 41-315X - by PhilcoMike - 01-10-2014, 03:39 PM

RE: Philco 41-315X - by Ron Ramirez - 01-10-2014, 05:57 PM

RE: Philco 41-315X - by jeffgniffke - 02-04-2014, 12:38 PM

RE: Philco 41-315X - by vinzer - 02-04-2014, 06:45 PM

RE: Philco 41-315X - by jeffgniffke - 06-09-2014, 06:18 PM

RE: Philco 41-315X - by bfrohwein - 06-09-2014, 07:08 PM

RE: Philco 41-315X - by bfrohwein - 06-09-2014, 07:14 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me