Philco 91 Code 126

Thread Rating:

1 Vote(s) - 5 Average
1
2
3
4
5

Linear Mode

Philco 91 Code 126

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

12-30-2013, 12:52 PM

I'm hip. I rewound the oscillator coil already. Perhaps I made a mistake in that? Well, I'll test the 36 tube before digging back into the coil.

Although it is tempting to perform one of my 6A7 mods to this set...

And Todd, thanks for the WD-40/Popsicle stick advice regarding the Mershons, sounds good, will have to try that.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 91 Code 126 - by Ron Ramirez - 12-29-2013, 09:20 PM

RE: Philco 91 Code 126 - by morzh - 12-29-2013, 09:36 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 12-29-2013, 09:38 PM

RE: Philco 91 Code 126 - by 37silverstreak - 12-29-2013, 09:43 PM

RE: Philco 91 Code 126 - by murf - 12-29-2013, 09:44 PM

RE: Philco 91 Code 126 - by morzh - 12-29-2013, 09:47 PM

RE: Philco 91 Code 126 - by tab10672 - 12-30-2013, 03:08 AM

RE: Philco 91 Code 126 - by TA Forbes - 12-30-2013, 11:31 AM

RE: Philco 91 Code 126 - by Ron Ramirez - 12-30-2013, 12:52 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 12-31-2013, 11:34 PM

RE: Philco 91 Code 126 - by morzh - 01-01-2014, 12:38 PM

RE: Philco 91 Code 126 - by TA Forbes - 01-01-2014, 02:41 PM

RE: Philco 91 Code 126 - by Mondial - 01-01-2014, 06:05 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-01-2014, 06:51 PM

RE: Philco 91 Code 126 - by Mondial - 01-01-2014, 07:20 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-01-2014, 09:36 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-03-2014, 10:41 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-04-2014, 11:38 PM

RE: Philco 91 Code 126 - by klondike98 - 01-05-2014, 10:28 AM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-05-2014, 11:12 AM

RE: Philco 91 Code 126 - by w4rtc - 01-05-2014, 12:12 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-05-2014, 01:42 PM

RE: Philco 91 Code 126 - by vinzer - 01-05-2014, 01:56 PM

RE: Philco 91 Code 126 - by morzh - 01-05-2014, 06:33 PM

RE: Philco 91 Code 126 - by TA Forbes - 01-06-2014, 02:33 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-06-2014, 05:00 PM

RE: Philco 91 Code 126 - by 37silverstreak - 01-06-2014, 07:42 PM

RE: Philco 91 Code 126 - by morzh - 01-06-2014, 07:50 PM

RE: Philco 91 Code 126 - by LASJayhawk - 01-07-2014, 02:17 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-07-2014, 08:12 PM

RE: Philco 91 Code 126 - by Ron Ramirez - 01-07-2014, 08:13 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

Who's Online

There are currently 3556 online users. [Complete List]
» 2 Member(s) | 3554 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me