Hello To All, Newbie here!

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hello To All, Newbie here!

morzh
Odobenus rosmarus

Posts: 16,480
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ

01-04-2014, 09:09 PM

I tell you this - if a cabinet is good, and the radio is the one I want, although I will cuss and spat when I find out the power tranny is pushing dasies, I will be chugging along with it as you can always find a transformer that will satisfy the electrical and power requirements and fits inside, and then there are ways of securing it.

It is a hassle though, a totally unwanted one, that I agree with. Plus a possible $100 setback.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Hello To All, Newbie here! - by tobor - 01-04-2014, 05:01 PM

RE: Hello To All, Newbie here! - by morzh - 01-04-2014, 05:10 PM

RE: Hello To All, Newbie here! - by tobor - 01-04-2014, 05:19 PM

RE: Hello To All, Newbie here! - by klondike98 - 01-04-2014, 05:31 PM

RE: Hello To All, Newbie here! - by klondike98 - 01-04-2014, 05:42 PM

RE: Hello To All, Newbie here! - by hsusmann - 01-04-2014, 06:06 PM

RE: Hello To All, Newbie here! - by morzh - 01-04-2014, 09:09 PM

RE: Hello To All, Newbie here! - by sam - 01-05-2014, 01:05 AM

RE: Hello To All, Newbie here! - by y2kbruce - 01-05-2014, 07:21 AM

RE: Hello To All, Newbie here! - by PhilcoJohn - 01-05-2014, 09:33 AM

RE: Hello To All, Newbie here! - by GarySP - 01-05-2014, 04:24 PM

RE: Hello To All, Newbie here! - by Tom Hamilton - 01-06-2014, 09:05 AM

RE: Hello To All, Newbie here! - by gregb - 01-07-2014, 04:30 PM

RE: Hello To All, Newbie here! - by Eric T - 01-10-2014, 11:14 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM

Who's Online

There are currently 1393 online users. [Complete List]
» 2 Member(s) | 1391 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me