1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 91 Code 126
morzh
Odobenus rosmarus
*****
Posts: 15,843
Threads: 555
Joined: Oct 2011
City: Jackson, NJ
#24

01-05-2014, 06:33 PM
The maximum I have ever seen is about 4 or so feet high when I lived in central Russia, in 80s. This was not overnight, but temps being very low the snow accumulated. So when we pushed the car through a narrow plowed corridor the snow was at the level with the car's roof.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 91 Code 126 - by Ron Ramirez - 12-29-2013, 09:20 PM
RE: Philco 91 Code 126 - by morzh - 12-29-2013, 09:36 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 12-29-2013, 09:38 PM
RE: Philco 91 Code 126 - by 37silverstreak - 12-29-2013, 09:43 PM
RE: Philco 91 Code 126 - by murf - 12-29-2013, 09:44 PM
RE: Philco 91 Code 126 - by morzh - 12-29-2013, 09:47 PM
RE: Philco 91 Code 126 - by tab10672 - 12-30-2013, 03:08 AM
RE: Philco 91 Code 126 - by TA Forbes - 12-30-2013, 11:31 AM
RE: Philco 91 Code 126 - by Ron Ramirez - 12-30-2013, 12:52 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 12-31-2013, 11:34 PM
RE: Philco 91 Code 126 - by morzh - 01-01-2014, 12:38 PM
RE: Philco 91 Code 126 - by TA Forbes - 01-01-2014, 02:41 PM
RE: Philco 91 Code 126 - by Mondial - 01-01-2014, 06:05 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-01-2014, 06:51 PM
RE: Philco 91 Code 126 - by Mondial - 01-01-2014, 07:20 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-01-2014, 09:36 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-03-2014, 10:41 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-04-2014, 11:38 PM
RE: Philco 91 Code 126 - by klondike98 - 01-05-2014, 10:28 AM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-05-2014, 11:12 AM
RE: Philco 91 Code 126 - by w4rtc - 01-05-2014, 12:12 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-05-2014, 01:42 PM
RE: Philco 91 Code 126 - by vinzer - 01-05-2014, 01:56 PM
RE: Philco 91 Code 126 - by morzh - 01-05-2014, 06:33 PM
RE: Philco 91 Code 126 - by TA Forbes - 01-06-2014, 02:33 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-06-2014, 05:00 PM
RE: Philco 91 Code 126 - by 37silverstreak - 01-06-2014, 07:42 PM
RE: Philco 91 Code 126 - by morzh - 01-06-2014, 07:50 PM
RE: Philco 91 Code 126 - by LASJayhawk - 01-07-2014, 02:17 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-07-2014, 08:12 PM
RE: Philco 91 Code 126 - by Ron Ramirez - 01-07-2014, 08:13 PM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration