Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Any idea on this model?
#10

Thanks for the feedback fellas. Its sincerely appreciated.

I have to wonder under what circumstances this radio was made. Perhaps a cabinet maker who had the radio but a damaged cabinet or someone simply testing their skills.

How often have you run across this?


Messages In This Thread
Any idea on this model? - by WyTex - 01-10-2014, 09:33 AM
RE: Any idea on this model? - by Ron Ramirez - 01-10-2014, 12:45 PM
RE: Any idea on this model? - by WyTex - 01-10-2014, 04:23 PM
RE: Any idea on this model? - by klondike98 - 01-10-2014, 04:34 PM
RE: Any idea on this model? - by WyTex - 01-10-2014, 04:48 PM
RE: Any idea on this model? - by Ron Ramirez - 01-10-2014, 04:49 PM
RE: Any idea on this model? - by morzh - 01-10-2014, 05:28 PM
RE: Any idea on this model? - by WyTex - 01-10-2014, 05:31 PM
RE: Any idea on this model? - by Ron Ramirez - 01-10-2014, 05:39 PM
RE: Any idea on this model? - by WyTex - 01-10-2014, 06:41 PM
RE: Any idea on this model? - by Eric T - 01-10-2014, 10:54 PM
RE: Any idea on this model? - by hsusmann - 01-10-2014, 11:30 PM
RE: Any idea on this model? - by jontz - 01-10-2014, 11:34 PM
RE: Any idea on this model? - by hsusmann - 01-10-2014, 11:41 PM
RE: Any idea on this model? - by JimZ - 01-11-2014, 10:18 AM
RE: Any idea on this model? - by Jamie - 01-11-2014, 10:45 AM
RE: Any idea on this model? - by Ron Ramirez - 01-11-2014, 03:19 PM
RE: Any idea on this model? - by klondike98 - 01-11-2014, 03:28 PM
RE: Any idea on this model? - by Joe Rossi - 01-11-2014, 05:27 PM
RE: Any idea on this model? - by WyTex - 01-11-2014, 10:19 PM
RE: Any idea on this model? - by Ron Ramirez - 01-11-2014, 10:44 PM
RE: Any idea on this model? - by Arran - 01-12-2014, 02:20 AM
RE: Any idea on this model? - by Joeztech - 01-12-2014, 12:20 PM
RE: Any idea on this model? - by Paul Philco322 - 01-12-2014, 03:21 PM
RE: Any idea on this model? - by LASJayhawk - 01-12-2014, 09:01 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>