Any idea on this model?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Any idea on this model?

JimZ
Member

Posts: 114
Threads: 2
Joined: Jan 2014
City: Southport NC

#15

01-11-2014, 10:18 AM

Hello all...new member and first post here. Id sure agree the chassis/dial are probably out of an old PT 25 that was left homeless.
I also remember this particular set and where it was listed. Sellers might do well to suggest a homebrew/other cabinet than play up the "unknown model"
angle. Ive gotten so I assume "homebrew" whenever I cant find a clear ID...particularly with a Philco as the models are very well documented.

More general note. I enjoy reading here and appreciate the depth of information and all the effort involved....even if I only own a few Philco models.
Nobody will ever pry my PT 44/ PT 7 etc from my fingers.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Any idea on this model? - by WyTex - 01-10-2014, 09:33 AM

RE: Any idea on this model? - by Ron Ramirez - 01-10-2014, 12:45 PM

RE: Any idea on this model? - by WyTex - 01-10-2014, 04:23 PM

RE: Any idea on this model? - by klondike98 - 01-10-2014, 04:34 PM

RE: Any idea on this model? - by WyTex - 01-10-2014, 04:48 PM

RE: Any idea on this model? - by Ron Ramirez - 01-10-2014, 04:49 PM

RE: Any idea on this model? - by morzh - 01-10-2014, 05:28 PM

RE: Any idea on this model? - by WyTex - 01-10-2014, 05:31 PM

RE: Any idea on this model? - by Ron Ramirez - 01-10-2014, 05:39 PM

RE: Any idea on this model? - by WyTex - 01-10-2014, 06:41 PM

RE: Any idea on this model? - by Eric T - 01-10-2014, 10:54 PM

RE: Any idea on this model? - by hsusmann - 01-10-2014, 11:30 PM

RE: Any idea on this model? - by jontz - 01-10-2014, 11:34 PM

RE: Any idea on this model? - by hsusmann - 01-10-2014, 11:41 PM

RE: Any idea on this model? - by JimZ - 01-11-2014, 10:18 AM

RE: Any idea on this model? - by Jamie - 01-11-2014, 10:45 AM

RE: Any idea on this model? - by Ron Ramirez - 01-11-2014, 03:19 PM

RE: Any idea on this model? - by klondike98 - 01-11-2014, 03:28 PM

RE: Any idea on this model? - by Joe Rossi - 01-11-2014, 05:27 PM

RE: Any idea on this model? - by WyTex - 01-11-2014, 10:19 PM

RE: Any idea on this model? - by Ron Ramirez - 01-11-2014, 10:44 PM

RE: Any idea on this model? - by Arran - 01-12-2014, 02:20 AM

RE: Any idea on this model? - by Joeztech - 01-12-2014, 12:20 PM

RE: Any idea on this model? - by Paul Philco322 - 01-12-2014, 03:21 PM

RE: Any idea on this model? - by LASJayhawk - 01-12-2014, 09:01 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 4460 online users. [Complete List]
» 5 Member(s) | 4455 Guest(s)