1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
The vacuum tube tester
fields 100
Member
***
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
#1

01-15-2014, 10:44 AM
Can you, guys, advise me on the decent tube tester? With all other expenses
I can't shell out a lot, but at the same time do not want to get a junk,hence I am here again. There are plenty of those on the E-bay site, but in my budget category the only thing I can read in the description is "powers up" and no more. In case I pick up the "powers up" one, how difficult to bring it, if needed, to the operational condition? Thanks.
Find
« Next Oldest | Next Newest »


Messages In This Thread
The vacuum tube tester - by fields 100 - 01-15-2014, 10:44 AM
RE: The vacuum tube tester - by hsusmann - 01-15-2014, 11:13 AM
RE: The vacuum tube tester - by TA Forbes - 01-15-2014, 11:41 AM
RE: The vacuum tube tester - by morzh - 01-15-2014, 12:03 PM
RE: The vacuum tube tester - by hsusmann - 01-15-2014, 01:19 PM
RE: The vacuum tube tester - by morzh - 01-15-2014, 02:35 PM
RE: The vacuum tube tester - by Bradley Rush - 01-15-2014, 03:14 PM
RE: The vacuum tube tester - by TA Forbes - 01-16-2014, 10:50 AM
RE: The vacuum tube tester - by Jamie - 01-17-2014, 08:23 PM
RE: The vacuum tube tester - by TA Forbes - 01-17-2014, 10:34 PM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration