1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Hello from new member
Tom Hamilton
Member
***
Posts: 120
Threads: 10
Joined: Jul 2011
City: Glendale, CA
#6

01-16-2014, 01:24 PM
Hey Tim,

Welcome to the Phorum!

As you'll soon find out, there's lots of good information here.

Tom
Find
« Next Oldest | Next Newest »


Messages In This Thread
Hello from new member - by tim1 - 01-15-2014, 11:21 PM
RE: Hello from new member - by klondike98 - 01-16-2014, 07:59 AM
RE: Hello from new member - by Eric Adams - 01-16-2014, 09:31 AM
RE: Hello from new member - by TA Forbes - 01-16-2014, 09:38 AM
RE: Hello from new member - by hsusmann - 01-16-2014, 09:52 AM
RE: Hello from new member - by Tom Hamilton - 01-16-2014, 01:24 PM
RE: Hello from new member - by codefox1 - 01-16-2014, 04:41 PM
RE: Hello from new member - by gregb - 01-16-2014, 05:08 PM
RE: Hello from new member - by GarySP - 01-18-2014, 02:53 PM
RE: Hello from new member - by PAradiogeek - 01-18-2014, 09:00 PM
RE: Hello from new member - by Eric T - 01-18-2014, 09:28 PM
RE: Hello from new member - by Ron Ramirez - 01-19-2014, 09:40 AM
RE: Hello from new member - by KCMike - 01-19-2014, 03:55 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios