1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
where! 3 and 4 lead caps.
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#5

01-17-2014, 08:54 PM
Yes Brenda,
They are replacements, They were spliced in, not even soldered. One is supposed to be 100mfd and the other should be a 30.
For the 20 + 20 with 2 leads out each end. I would get 2 20 mfd caps and and just twist one ends leads together and run the other 2 to their separate terminals and pins?

Thanks for the help
Kirk
Find
« Next Oldest | Next Newest »


Messages In This Thread
where! 3 and 4 lead caps. - by OldRestorer - 01-17-2014, 06:13 PM
RE: where! 3 and 4 lead caps. - by Jamie - 01-17-2014, 06:21 PM
RE: where! 3 and 4 lead caps. - by BrendaAnnD - 01-17-2014, 06:35 PM
RE: where! 3 and 4 lead caps. - by morzh - 01-17-2014, 08:31 PM
RE: where! 3 and 4 lead caps. - by OldRestorer - 01-17-2014, 08:54 PM
RE: where! 3 and 4 lead caps. - by Jamie - 01-17-2014, 09:26 PM
RE: where! 3 and 4 lead caps. - by TV MAN - 01-18-2014, 12:28 AM
RE: where! 3 and 4 lead caps. - by BrendaAnnD - 01-18-2014, 03:06 AM
RE: where! 3 and 4 lead caps. - by OldRestorer - 01-18-2014, 09:02 AM
RE: where! 3 and 4 lead caps. - by codefox1 - 01-18-2014, 06:40 PM
RE: where! 3 and 4 lead caps. - by OldRestorer - 01-18-2014, 06:56 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently 2254 online users. [Complete List]
» 3 Member(s) | 2251 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration