Getting back into my 20

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Getting back into my 20

morzh
Odobenus rosmarus

Posts: 16,482
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ

01-19-2014, 02:44 PM

1. I would not touch coils if they work. Your borrowed time might be longer than any of our lives that we have left.
2. Chord is a good idea.
3. What is dirty GND? How is it dirty? If it is dirty, your Y is gonna hurt you not help you.
4. typica vlues for X is 0.1 to 1 uF, and if it is before the switch on the power side then install a bleed resistor across. Otherwise no resistor needed.
5. Typical Y is up to 3nF, but if you have isolation and no touch of chassis is possible 10nF is OK too.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Getting back into my 20 - by GarySP - 01-19-2014, 12:47 PM

RE: Getting back into my 20 - by morzh - 01-19-2014, 02:44 PM

RE: Getting back into my 20 - by GarySP - 01-19-2014, 03:07 PM

RE: Getting back into my 20 - by Phlogiston - 01-19-2014, 03:44 PM

RE: Getting back into my 20 - by tab10672 - 01-19-2014, 03:47 PM

RE: Getting back into my 20 - by GarySP - 01-21-2014, 10:15 AM

RE: Getting back into my 20 - by tab10672 - 01-21-2014, 02:22 PM

RE: Getting back into my 20 - by GarySP - 01-22-2014, 01:21 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

Who's Online

There are currently 1034 online users. [Complete List]
» 2 Member(s) | 1032 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me