1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
New Flea Market found and Philcos!
Randy H.
Junior Member
**
Posts: 28
Threads: 0
Joined: Nov 2013
City: Tucson, AZ
#13

01-26-2014, 07:56 PM
Jayce,
Isn't THAT just nice? Here in Tucson they have been 'renovating' the Downtown area for about 10 years. Lots of lost busineses. On the North side they widened a road for so long, and tied up an intersection for so long that about 7 businesses went out in one center alone. You could not get in. And they didn't care!
Find
« Next Oldest | Next Newest »


Messages In This Thread
New Flea Market found and Philcos! - by Jayce - 09-08-2012, 08:17 PM
RE: New Flea Market found and Philcos! - by Jayce - 09-08-2012, 09:06 PM
RE: New Flea Market found and Philcos! - by Jayce - 09-10-2012, 07:30 PM
RE: New Flea Market found and Philcos! - by gregb - 01-24-2014, 02:08 PM
RE: New Flea Market found and Philcos! - by Jayce - 01-24-2014, 03:40 PM
RE: New Flea Market found and Philcos! - by Randy H. - 01-26-2014, 07:56 PM
RE: New Flea Market found and Philcos! - by Jayce - 01-26-2014, 08:01 PM
RE: New Flea Market found and Philcos! - by Arran - 01-27-2014, 10:28 PM
RE: New Flea Market found and Philcos! - by Jayce - 01-28-2014, 12:23 AM
RE: New Flea Market found and Philcos! - by Arran - 01-28-2014, 04:26 AM
RE: New Flea Market found and Philcos! - by Jamie - 01-28-2014, 05:07 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4607 online users. [Complete List]
» 1 Member(s) | 4606 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios