Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

replacing a dual Ecap with 2
#26

I think you mean part 29. The negatives are tied together and go to the center tap of the high voltage windings on the transformer.

Positive on the 8uf goes to the B+ from the 80 tube, either pin 1 or 4. It also goes to a .015 cap (in bakelite), and the field coil.

The 4uf connects to the other side of the field coil, the other side of that .015 cap, and the B+ supply to the rest of the radio.


Messages In This Thread
replacing a dual Ecap with 2 - by OldRestorer - 01-24-2014, 09:39 PM
RE: replacing a dual Ecap with 2 - by gregb - 01-24-2014, 09:53 PM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-24-2014, 10:03 PM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-24-2014, 10:12 PM
RE: replacing a dual Ecap with 2 - by klondike98 - 01-24-2014, 10:16 PM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-24-2014, 10:24 PM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-24-2014, 10:26 PM
RE: replacing a dual Ecap with 2 - by gregb - 01-24-2014, 10:35 PM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-24-2014, 10:39 PM
RE: replacing a dual Ecap with 2 - by gregb - 01-24-2014, 10:40 PM
RE: replacing a dual Ecap with 2 - by morzh - 01-24-2014, 10:58 PM
RE: replacing a dual Ecap with 2 - by Joe Rossi - 01-25-2014, 08:16 AM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-25-2014, 08:18 AM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-25-2014, 10:35 AM
RE: replacing a dual Ecap with 2 - by gregb - 01-25-2014, 12:18 PM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-26-2014, 08:01 AM
RE: replacing a dual Ecap with 2 - by Ron Ramirez - 01-26-2014, 10:05 AM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-26-2014, 10:13 AM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-26-2014, 10:51 AM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-26-2014, 11:10 AM
RE: replacing a dual Ecap with 2 - by gregb - 01-26-2014, 11:26 AM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-26-2014, 01:12 PM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-26-2014, 01:57 PM
RE: replacing a dual Ecap with 2 - by klondike98 - 01-26-2014, 02:05 PM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-26-2014, 03:30 PM
RE: replacing a dual Ecap with 2 - by skyscraper - 01-26-2014, 08:32 PM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-27-2014, 09:54 AM
RE: replacing a dual Ecap with 2 - by gregb - 01-27-2014, 10:09 AM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-27-2014, 11:16 AM
RE: replacing a dual Ecap with 2 - by OldRestorer - 01-27-2014, 01:44 PM
RE: replacing a dual Ecap with 2 - by gregb - 01-27-2014, 01:56 PM
RE: replacing a dual Ecap with 2 - by OldRestorer - 02-05-2014, 08:11 AM
RE: replacing a dual Ecap with 2 - by gregb - 02-05-2014, 11:53 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently 1707 online users. [Complete List]
» 1 Member(s) | 1706 Guest(s)
Avatar

>