Hello Philco Phorum

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hello Philco Phorum

RadioDave
Junior Member

Posts: 15
Threads: 1
Joined: Jan 2014
City: Fort Washington, MD

#10

01-31-2014, 12:10 AM

Plate voltage...????... I've never been shocked by any of our melamine plates. Icon_lol

But that little 5" battery powered B&W tv set I swore was fully discharged after removing all 8 D cells and letting it sit for a month sure got my attention when I reached in the back. Icon_redface

No worries morzh, I have an isolation transformer. Just have to figure out how to use it! Icon_wink

Come to think of it, I have a couple of isolation transformers. Would two in series make it double safe? Or should that be parallel........ Icon_e_biggrin

Did I mention I'm not good with electronics?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Hello Philco Phorum - by RadioDave - 01-30-2014, 01:13 PM

RE: Hello Philco Phorum - by OldRestorer - 01-30-2014, 10:16 PM

RE: Hello Philco Phorum - by skyscraper - 01-30-2014, 10:31 PM

RE: Hello Philco Phorum - by TA Forbes - 01-30-2014, 10:45 PM

RE: Hello Philco Phorum - by RadioDave - 01-30-2014, 10:54 PM

RE: Hello Philco Phorum - by morzh - 01-30-2014, 10:55 PM

RE: Hello Philco Phorum - by klondike98 - 01-30-2014, 10:56 PM

RE: Hello Philco Phorum - by RadioDave - 01-30-2014, 11:26 PM

RE: Hello Philco Phorum - by morzh - 01-30-2014, 11:41 PM

RE: Hello Philco Phorum - by RadioDave - 01-31-2014, 12:10 AM

RE: Hello Philco Phorum - by skyscraper - 01-31-2014, 12:33 AM

RE: Hello Philco Phorum - by RadioDave - 01-31-2014, 01:03 AM

RE: Hello Philco Phorum - by OldRestorer - 01-31-2014, 07:53 AM

RE: Hello Philco Phorum - by PhilcoJohn - 02-01-2014, 08:25 PM

RE: Hello Philco Phorum - by RadioDave - 02-01-2014, 09:11 PM

RE: Hello Philco Phorum - by TA Forbes - 02-02-2014, 12:55 PM

RE: Hello Philco Phorum - by RadioDave - 02-02-2014, 02:36 PM

RE: Hello Philco Phorum - by GarySP - 02-02-2014, 06:27 PM

RE: Hello Philco Phorum - by Eric T - 02-02-2014, 06:34 PM

RE: Hello Philco Phorum - by codefox1 - 02-02-2014, 08:37 PM

RE: Hello Philco Phorum - by RadioDave - 02-02-2014, 09:25 PM

RE: Hello Philco Phorum - by RadioDave - 02-02-2014, 10:40 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me