Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Hello Philco Phorum
#21

The known problems so far are the lack of a speaker and some disconnected wires on the underside of the chassis. The speaker problem is most likely the easiest to solve and TA Forbes is helping me with that. Thanks TA!!

The wires are coming from two of the electrolytic capacitors. I'll be needing some schematic study time to figure those out.

There is one incorrect tube in the set and the condition of the others hasn't been determined yet. The incorrect tube is a GE 35/51 (with 35 being over number 51 on the side of the tube) where a type 24 is supposed to be. The location on the chassis is to the left of the type 27 at the back of the chassis behind the tuning capacitor. Can you tell I need some schematic study time? Icon_biggrin If I knew what I was talking about I could tell you if it was the RF, the 1st detector, or the IF. Icon_redface Icon_redface

Once these things are corrected I can bring it up real slow and look for the smoke signals to determine what else needs repair.

Thanks for asking codefox1!


Messages In This Thread
Hello Philco Phorum - by RadioDave - 01-30-2014, 01:13 PM
RE: Hello Philco Phorum - by OldRestorer - 01-30-2014, 10:16 PM
RE: Hello Philco Phorum - by skyscraper - 01-30-2014, 10:31 PM
RE: Hello Philco Phorum - by TA Forbes - 01-30-2014, 10:45 PM
RE: Hello Philco Phorum - by RadioDave - 01-30-2014, 10:54 PM
RE: Hello Philco Phorum - by morzh - 01-30-2014, 10:55 PM
RE: Hello Philco Phorum - by klondike98 - 01-30-2014, 10:56 PM
RE: Hello Philco Phorum - by RadioDave - 01-30-2014, 11:26 PM
RE: Hello Philco Phorum - by morzh - 01-30-2014, 11:41 PM
RE: Hello Philco Phorum - by RadioDave - 01-31-2014, 12:10 AM
RE: Hello Philco Phorum - by skyscraper - 01-31-2014, 12:33 AM
RE: Hello Philco Phorum - by RadioDave - 01-31-2014, 01:03 AM
RE: Hello Philco Phorum - by OldRestorer - 01-31-2014, 07:53 AM
RE: Hello Philco Phorum - by PhilcoJohn - 02-01-2014, 08:25 PM
RE: Hello Philco Phorum - by RadioDave - 02-01-2014, 09:11 PM
RE: Hello Philco Phorum - by TA Forbes - 02-02-2014, 12:55 PM
RE: Hello Philco Phorum - by RadioDave - 02-02-2014, 02:36 PM
RE: Hello Philco Phorum - by GarySP - 02-02-2014, 06:27 PM
RE: Hello Philco Phorum - by Eric T - 02-02-2014, 06:34 PM
RE: Hello Philco Phorum - by codefox1 - 02-02-2014, 08:37 PM
RE: Hello Philco Phorum - by RadioDave - 02-02-2014, 09:25 PM
RE: Hello Philco Phorum - by RadioDave - 02-02-2014, 10:40 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4400 online users. [Complete List]
» 4 Member(s) | 4396 Guest(s)
AvatarAvatarAvatarAvatar

>