Philco 620B alignment woes

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 620B alignment woes

BDM
Senior Member

Posts: 393
Threads: 40
Joined: Sep 2007
City: St Clair Shores, MI, USA

#12

06-21-2008, 11:56 PM

Bill, has the set been fully re-capped? Did you check the values against the schematic. I see cap #23 should be an .05/mf. Is it? I could see that cap being off or bad, effecting all the RF trimmers. It sounds like the capacitance is too high, and you're not able to trim low enough. Someone please correct if I'm wrong.

-Brian
If you collect or are interested in antique telephones, please visit Classic Rotary Phones
http://www.classicrotaryphones.com/forum/index.php

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 620B alignment woes - by wonderwrench - 06-19-2008, 06:29 PM

[No subject] - by wonderwrench - 06-20-2008, 07:02 PM

[No subject] - by BDM - 06-20-2008, 07:19 PM

[No subject] - by wonderwrench - 06-20-2008, 07:46 PM

[No subject] - by BDM - 06-20-2008, 07:58 PM

[No subject] - by wonderwrench - 06-20-2008, 08:03 PM

[No subject] - by wonderwrench - 06-21-2008, 11:52 AM

[No subject] - by BDM - 06-21-2008, 12:24 PM

[No subject] - by wonderwrench - 06-21-2008, 12:51 PM

[No subject] - by BDM - 06-21-2008, 01:16 PM

[No subject] - by rghines1 - 06-21-2008, 01:33 PM

[No subject] - by BDM - 06-21-2008, 11:56 PM

[No subject] - by wonderwrench - 06-23-2008, 03:26 PM

[No subject] - by wonderwrench - 06-23-2008, 04:03 PM

[No subject] - by etech - 06-23-2008, 06:33 PM

[No subject] - by wonderwrench - 06-29-2008, 06:23 PM

[No subject] - by wonderwrench - 07-06-2008, 12:26 PM

[No subject] - by Ron Ramirez - 07-06-2008, 02:46 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me