Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Need Advice Again: Philco 38-7 Console
#2

If you can get the guy down towards $40 you might have a decent bargain. The 38-4 and 38-7 had the same dial (concentric tuning) but the 38-4 is an 8 tube model where the 38-7 has only 6 (if not mistaken). These are nice models with well made cabinets but they are quite common with a ton of them made. Again it is a judgement call on the price but I would try to work the seller down as much as possible, while the cost of shipping is not an issue the price is higher than what you would see them for on ebay and some of Philcos higher tube count 38-38 models are going for around the same price.


Messages In This Thread
[No subject] - by 49Stude63 - 06-23-2008, 03:23 PM
[No subject] - by Michael Dennis - 06-24-2008, 09:55 AM
[No subject] - by phly guy - 06-24-2008, 10:48 AM
[No subject] - by Michael Dennis - 06-24-2008, 12:27 PM
[No subject] - by 49Stude63 - 06-24-2008, 03:43 PM
[No subject] - by Michael Dennis - 06-24-2008, 09:22 PM
[No subject] - by Texasrocker - 06-24-2008, 11:16 PM
[No subject] - by Michael Dennis - 06-25-2008, 01:09 AM
[No subject] - by gary rabbitt - 06-25-2008, 03:14 PM
[No subject] - by Michael Dennis - 06-25-2008, 03:50 PM
[No subject] - by Texasrocker - 06-27-2008, 02:24 AM
[No subject] - by Michael Dennis - 06-27-2008, 05:49 AM
[No subject] - by Texasrocker - 06-29-2008, 12:00 AM
[No subject] - by Michael Dennis - 06-29-2008, 04:12 AM
[No subject] - by Texasrocker - 07-01-2008, 01:01 AM
[No subject] - by Michael Dennis - 07-01-2008, 04:18 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3985 online users. [Complete List]
» 1 Member(s) | 3984 Guest(s)
Avatar

>