1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 46-1203
morzh
Odobenus rosmarus
*****
Posts: 15,825
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#18

02-07-2014, 04:27 PM
Those have to be electrolytics I think. I also think it is a doubling rectifier so the voltage ratings you use have to be about 350V. That is 250V DC will not be exceeded if the load is disconnected (hence the 350V rating to have margin) and normally it is lower (175/110V for 40uF and 10uF respectively) but this is if the load is OK.

So, use electrolytics 40uF and 10uF 350V.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 46-1203 - by Colorado Jeff - 10-18-2013, 12:11 PM
RE: Philco 46-1203 - by klondike98 - 10-18-2013, 05:07 PM
RE: Philco 46-1203 - by Colorado Jeff - 10-18-2013, 07:28 PM
RE: Philco 46-1203 - by klondike98 - 10-18-2013, 08:35 PM
RE: Philco 46-1203 - by Colorado Jeff - 10-30-2013, 09:53 AM
RE: Philco 46-1203 - by Colorado Jeff - 10-30-2013, 10:44 AM
RE: Philco 46-1203 - by klondike98 - 10-30-2013, 11:03 AM
RE: Philco 46-1203 - by klondike98 - 10-30-2013, 11:06 AM
RE: Philco 46-1203 - by Colorado Jeff - 10-30-2013, 12:30 PM
RE: Philco 46-1203 - by codefox1 - 10-30-2013, 03:00 PM
RE: Philco 46-1203 - by klondike98 - 10-30-2013, 06:49 PM
RE: Philco 46-1203 - by Colorado Jeff - 02-07-2014, 01:13 PM
RE: Philco 46-1203 - by morzh - 02-07-2014, 02:31 PM
RE: Philco 46-1203 - by Colorado Jeff - 02-07-2014, 02:38 PM
RE: Philco 46-1203 - by skyscraper - 02-07-2014, 03:00 PM
RE: Philco 46-1203 - by morzh - 02-07-2014, 03:00 PM
RE: Philco 46-1203 - by Colorado Jeff - 02-07-2014, 04:21 PM
RE: Philco 46-1203 - by morzh - 02-07-2014, 04:27 PM
RE: Philco 46-1203 - by Colorado Jeff - 02-08-2014, 11:19 PM
RE: Philco 46-1203 - by wa2ise - 02-09-2014, 01:09 AM



Users browsing this thread: 10 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration