Aligning 40-155...signal bleeding in

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Aligning 40-155...signal bleeding in

jeffgniffke
Junior Member

Posts: 46
Threads: 7
Joined: Apr 2013
City: Grand Marais, MN 55604

#17

02-09-2014, 07:55 PM

Restrung the antennae with a continuous wire...again a little better. Have some RF can wire to redo. BUT what is very noticeable now when the thing is dong its oscillating i push down on the mixer and it will quit...I knew that socket material was cracked...I ordered a new socket. I wonder it that is what side lined it to begin with back in the day?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Aligning 40-155...signal bleeding in - by jeffgniffke - 01-26-2014, 08:04 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 01-26-2014, 09:26 PM

RE: Aligning 40-155...signal bleeding in - by Radioroslyn - 01-27-2014, 12:09 AM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 01-27-2014, 05:05 PM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 01-27-2014, 07:56 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 01-28-2014, 01:03 AM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 01-28-2014, 08:52 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 01-29-2014, 10:31 AM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 01-30-2014, 01:20 AM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 01-30-2014, 05:14 PM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 02-03-2014, 05:18 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 02-03-2014, 11:38 PM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 02-07-2014, 05:34 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 02-08-2014, 01:51 AM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 02-08-2014, 10:37 AM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 02-09-2014, 12:20 PM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 02-09-2014, 07:55 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 02-10-2014, 01:03 AM

RE: Aligning 40-155...signal bleeding in - by jeffgniffke - 02-22-2014, 10:55 PM

RE: Aligning 40-155...signal bleeding in - by Raleigh - 02-23-2014, 02:08 AM

RE: Aligning 40-155...signal bleeding in - by DeckApe - 02-25-2014, 12:18 PM

RE: Aligning 40-155...signal bleeding in - by K7Sparky - 04-06-2014, 12:39 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me