Alignment Questions

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Alignment Questions

Warren
Senior Member

Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California

02-10-2014, 02:01 AM

Any certain type of wire I should use? Probably uninsulated, any certain gauge, stranded, solid? I might have some old guy wire around if that would work. I noticed in the instructions they want you to make a 6 inch around loop about 4 to 6 turns to hook up to the generator for some of the alignment steps.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Alignment Questions - by Warren - 02-10-2014, 12:08 AM

RE: Alignment Questions - by tab10672 - 02-10-2014, 12:58 AM

RE: Alignment Questions - by Warren - 02-10-2014, 01:29 AM

RE: Alignment Questions - by Raleigh - 02-10-2014, 01:48 AM

RE: Alignment Questions - by Raleigh - 02-10-2014, 02:00 AM

RE: Alignment Questions - by Warren - 02-10-2014, 02:01 AM

RE: Alignment Questions - by Raleigh - 02-10-2014, 02:13 AM

RE: Alignment Questions - by Warren - 02-10-2014, 02:57 AM

RE: Alignment Questions - by tab10672 - 02-10-2014, 09:43 AM

RE: Alignment Questions - by tab10672 - 02-10-2014, 09:46 AM

RE: Alignment Questions - by Raleigh - 02-10-2014, 01:17 PM

RE: Alignment Questions - by Warren - 02-10-2014, 02:51 PM

RE: Alignment Questions - by Warren - 02-11-2014, 06:03 PM

RE: Alignment Questions - by Warren - 02-12-2014, 04:38 PM

RE: Alignment Questions - by tab10672 - 02-12-2014, 08:00 PM

RE: Alignment Questions - by Warren - 02-12-2014, 11:39 PM

RE: Alignment Questions - by tab10672 - 02-13-2014, 03:15 PM

RE: Alignment Questions - by jerryhawthorne - 02-13-2014, 03:48 PM

RE: Alignment Questions - by Warren - 02-13-2014, 04:34 PM

RE: Alignment Questions - by Warren - 02-14-2014, 12:51 AM

RE: Alignment Questions - by tab10672 - 02-14-2014, 01:29 AM

RE: Alignment Questions - by Warren - 02-14-2014, 01:59 AM

RE: Alignment Questions - by tab10672 - 02-14-2014, 02:07 AM

RE: Alignment Questions - by tab10672 - 02-14-2014, 02:13 AM

RE: Alignment Questions - by Warren - 02-14-2014, 03:12 AM

RE: Alignment Questions - by tab10672 - 02-14-2014, 01:48 PM

RE: Alignment Questions - by Raleigh - 02-14-2014, 02:45 PM

RE: Alignment Questions - by Warren - 02-14-2014, 04:24 PM

RE: Alignment Questions - by Raleigh - 02-14-2014, 06:07 PM

View a Printable Version

Users browsing this thread: 15 Guest(s)

Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me