Starting work on my 19B

Thread Rating:

1 Vote(s) - 5 Average
1
2
3
4
5

Linear Mode

Starting work on my 19B

PAradiogeek
Senior Member

Posts: 395
Threads: 33
Joined: Jul 2013
City: Horsham, PA

#35

02-16-2014, 12:03 AM

Hey, I actually got back to work on this radio tonight Icon_smile

. I looked in my notes and the last time I worked on it was a month ago. Been a busy month.

I placed a new electrolytic in C44 and got it back in the chassis. Then I decided to test the on/off switch continuity while I still had that switch partially out of the chassis. I removed a wire from one of the switch terminals and tested. In one position I get an open as expected, but in the other two positions, I get readings all over the map from ~3K ohms to as low as ~60 ohms.

I know I need to clean the switch, but what is an acceptable reading for a closed switch? Should it be in the neighborhood of .1 ohm, or is something a little higher acceptable?

Thanks,
Jon

Find

« Next Oldest | Next Newest »

Messages In This Thread

Starting work on my 19B - by PAradiogeek - 12-06-2013, 12:16 AM

RE: Starting work on my 19B - by BrendaAnnD - 12-06-2013, 06:49 AM

RE: Starting work on my 19B - by Mondial - 12-06-2013, 08:35 AM

RE: Starting work on my 19B - by PAradiogeek - 12-06-2013, 11:44 AM

RE: Starting work on my 19B - by PAradiogeek - 12-11-2013, 10:02 PM

RE: Starting work on my 19B - by BrendaAnnD - 12-11-2013, 10:28 PM

RE: Starting work on my 19B - by PAradiogeek - 12-12-2013, 02:49 PM

RE: Starting work on my 19B - by BrendaAnnD - 12-12-2013, 03:19 PM

RE: Starting work on my 19B - by codefox1 - 12-12-2013, 08:20 PM

RE: Starting work on my 19B - by morzh - 12-12-2013, 11:41 PM

RE: Starting work on my 19B - by PAradiogeek - 12-13-2013, 08:34 AM

RE: Starting work on my 19B - by jerryhawthorne - 12-13-2013, 07:48 PM

RE: Starting work on my 19B - by klondike98 - 12-13-2013, 07:59 PM

RE: Starting work on my 19B - by Radioroslyn - 12-15-2013, 12:53 PM

RE: Starting work on my 19B - by PAradiogeek - 12-15-2013, 09:37 PM

RE: Starting work on my 19B - by jerryhawthorne - 12-15-2013, 10:11 PM

RE: Starting work on my 19B - by PAradiogeek - 12-16-2013, 08:55 PM

RE: Starting work on my 19B - by PAradiogeek - 12-19-2013, 11:30 PM

RE: Starting work on my 19B - by klondike98 - 12-19-2013, 11:50 PM

RE: Starting work on my 19B - by Bradley Rush - 12-20-2013, 03:44 AM

RE: Starting work on my 19B - by PAradiogeek - 12-20-2013, 08:11 AM

RE: Starting work on my 19B - by jerryhawthorne - 12-20-2013, 06:16 PM

RE: Starting work on my 19B - by PAradiogeek - 12-25-2013, 04:40 PM

RE: Starting work on my 19B - by Ron Ramirez - 12-25-2013, 06:02 PM

RE: Starting work on my 19B - by morzh - 12-25-2013, 06:08 PM

RE: Starting work on my 19B - by PAradiogeek - 12-25-2013, 07:49 PM

RE: Starting work on my 19B - by morzh - 12-25-2013, 09:39 PM

RE: Starting work on my 19B - by PAradiogeek - 12-25-2013, 11:53 PM

RE: Starting work on my 19B - by tab10672 - 12-26-2013, 12:43 AM

RE: Starting work on my 19B - by morzh - 12-26-2013, 11:24 AM

RE: Starting work on my 19B - by PAradiogeek - 12-26-2013, 03:18 PM

RE: Starting work on my 19B - by PAradiogeek - 01-11-2014, 06:04 PM

RE: Starting work on my 19B - by PAradiogeek - 01-13-2014, 08:34 AM

RE: Starting work on my 19B - by PAradiogeek - 02-16-2014, 12:03 AM

RE: Starting work on my 19B - by morzh - 02-16-2014, 12:13 PM

RE: Starting work on my 19B - by PAradiogeek - 03-03-2014, 11:37 PM

RE: Starting work on my 19B - by PAradiogeek - 03-07-2014, 11:47 PM

RE: Starting work on my 19B - by Mondial - 03-08-2014, 12:00 AM

RE: Starting work on my 19B - by PAradiogeek - 03-19-2014, 09:20 PM

RE: Starting work on my 19B - by skyscraper - 03-19-2014, 09:38 PM

RE: Starting work on my 19B - by Mondial - 03-19-2014, 09:49 PM

RE: Starting work on my 19B - by skyscraper - 03-19-2014, 09:56 PM

RE: Starting work on my 19B - by Joeztech - 03-20-2014, 07:46 AM

RE: Starting work on my 19B - by PAradiogeek - 03-21-2014, 11:47 PM

RE: Starting work on my 19B - by jerryhawthorne - 03-22-2014, 12:35 AM

RE: Starting work on my 19B - by Joeztech - 03-22-2014, 06:50 AM

RE: Starting work on my 19B - by Mondial - 03-22-2014, 10:34 AM

RE: Starting work on my 19B - by Joeztech - 03-22-2014, 11:12 AM

RE: Starting work on my 19B - by PAradiogeek - 03-24-2014, 10:25 PM

RE: Starting work on my 19B - by skyscraper - 03-24-2014, 10:41 PM

RE: Starting work on my 19B - by PAradiogeek - 03-25-2014, 07:13 AM

RE: Starting work on my 19B - by morzh - 03-25-2014, 10:12 AM

RE: Starting work on my 19B - by Radioroslyn - 03-25-2014, 05:10 PM

RE: Starting work on my 19B - by PAradiogeek - 03-25-2014, 08:14 PM

RE: Starting work on my 19B - by PAradiogeek - 03-25-2014, 11:42 PM

RE: Starting work on my 19B - by skyscraper - 03-26-2014, 12:17 AM

RE: Starting work on my 19B - by PAradiogeek - 03-30-2014, 07:34 AM

RE: Starting work on my 19B - by Steve Davis - 03-30-2014, 08:57 AM

RE: Starting work on my 19B - by PAradiogeek - 03-30-2014, 11:21 AM

RE: Starting work on my 19B - by skyscraper - 03-30-2014, 12:32 PM

RE: Starting work on my 19B - by PAradiogeek - 03-30-2014, 04:50 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
identify very thin wire for replacement on 37-640
Thanks so much for your help! I really could not have gotten this far without the kindness of you and other members. T...georgetownjohn — 11:50 AM
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM
Philco 38-7 Speaker
Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM
Philco 38-7 Speaker
Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM
Philco 38-7 Oscillation
Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this. If you wa...morzh — 09:27 AM
identify very thin wire for replacement on 37-640
You can possibly use a heatshrink tubing. If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM
identify very thin wire for replacement on 37-640
Happy Thanksgiving, I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM
Philco 60 Squealing
I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM

Who's Online

There are currently 1341 online users. [Complete List]
» 4 Member(s) | 1337 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me