42-355 field coil gets very warm

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Guest
Unregistered

06-30-2008, 10:00 PM

Ok! I installed a 15 ohm, 25w resistor(and replaced the 2A with a 1A slo-blo fuse). The transformer and field coil run significantly cooler now. At 121vac, I'm getting around 114v at the transformer primary, past the resistor. Thanks so much for your help. -Karen

« Next Oldest | Next Newest »

Messages In This Thread

42-355 field coil gets very warm - by Guest - 06-28-2008, 07:44 PM

[No subject] - by Texasrocker - 06-29-2008, 01:33 AM

[No subject] - by Guest - 06-29-2008, 11:26 AM

[No subject] - by etech - 06-29-2008, 05:48 PM

[No subject] - by Guest - 06-30-2008, 10:00 PM

[No subject] - by Texasrocker - 07-01-2008, 01:21 AM

[No subject] - by justlrnin - 07-01-2008, 07:41 AM

[No subject] - by Ron Ramirez - 07-03-2008, 10:28 AM

[No subject] - by etech - 07-03-2008, 09:00 PM

[No subject] - by Guest - 07-04-2008, 01:46 PM

[No subject] - by etech - 07-04-2008, 06:07 PM

[No subject] - by Ron Ramirez - 07-04-2008, 06:57 PM

[No subject] - by BDM - 07-04-2008, 07:37 PM

[No subject] - by etech - 07-04-2008, 09:06 PM

[No subject] - by Texasrocker - 07-12-2008, 03:11 AM

[No subject] - by etech - 07-12-2008, 09:50 AM

[No subject] - by justlrnin - 07-14-2008, 06:36 PM

[No subject] - by FStephenMasek - 07-14-2008, 06:50 PM

[No subject] - by exray - 07-14-2008, 08:57 PM

[No subject] - by etech - 07-14-2008, 09:27 PM

[No subject] - by BDM - 07-15-2008, 12:41 AM

[No subject] - by exray - 07-15-2008, 02:47 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5725 online users. [Complete List]
» 1 Member(s) | 5724 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me