1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Restoration options
auplater
Junior Member
**
Posts: 15
Threads: 1
Joined: Jun 2008
#23

07-06-2008, 03:08 PM
Just an update if anyone's reading...

Recapped the electrolytics
[Image: http://i3.photobucket.com/albums/y62/aup...RECAP3.jpg]

Had to bore out the wax/tar/foil on the 3 cap can... carefully using a drillpress and a spade bit Icon_smile
[Image: http://i3.photobucket.com/albums/y62/auplater/BORE1.jpg]

Started further clean-up and touchup of the chasis...
[Image: http://i3.photobucket.com/albums/y62/aup...RECAP2.jpg]
[Image: http://i3.photobucket.com/albums/y62/aup...RECAP1.jpg]

Going to test the tubes this week... hopefully most will be operable.

Going well so far... now I gotta order some 1/2 watt resistors.... this may take 'till Xmas... Icon_mrgreen

John L.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Restoration options - by auplater - 06-18-2008, 09:35 PM
Re: Restoration options - by Ron Ramirez - 06-18-2008, 10:05 PM
[No subject] - by 49Stude63 - 06-18-2008, 11:01 PM
[No subject] - by philcobenz - 06-19-2008, 12:32 AM
Options - by auplater - 06-19-2008, 07:08 AM
[No subject] - by philcobenz - 06-19-2008, 11:36 AM
Refinishing - by auplater - 06-19-2008, 02:16 PM
Re: Options - by exray - 06-19-2008, 02:24 PM
[No subject] - by philcobenz - 06-19-2008, 03:37 PM
[No subject] - by 49Stude63 - 06-19-2008, 04:44 PM
Re: Options - by auplater - 06-21-2008, 04:49 PM
Fabric cleaned and reinstalled - by auplater - 06-21-2008, 06:38 PM
[No subject] - by Ron Ramirez - 06-21-2008, 09:53 PM
Tube Shields - by auplater - 06-23-2008, 07:35 PM
[No subject] - by philcobenz - 06-24-2008, 07:05 PM
[No subject] - by auplater - 06-24-2008, 07:44 PM
[No subject] - by Texasrocker - 06-25-2008, 02:48 AM
[No subject] - by auplater - 06-25-2008, 08:38 AM
[No subject] - by Texasrocker - 06-27-2008, 02:18 AM
Plating - by auplater - 07-01-2008, 08:29 AM
[No subject] - by Texasrocker - 07-02-2008, 01:15 AM
Restoration progress - by auplater - 07-02-2008, 08:51 AM
progress made - by auplater - 07-06-2008, 03:08 PM
Re: Restoration progress - by Ron Ramirez - 07-06-2008, 04:50 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration