1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
42-355 field coil gets very warm
etech
Member
***
Posts: 237
Threads: 24
Joined: Dec 2007
City: Gladwin, MI
#16

07-12-2008, 09:50 AM
Randal,

Thanks for the offer of the nichrome wire. I will keep it in mind.

Ed
Find
« Next Oldest | Next Newest »


Messages In This Thread
42-355 field coil gets very warm - by Guest - 06-28-2008, 07:44 PM
[No subject] - by Texasrocker - 06-29-2008, 01:33 AM
[No subject] - by Guest - 06-29-2008, 11:26 AM
[No subject] - by etech - 06-29-2008, 05:48 PM
[No subject] - by Guest - 06-30-2008, 10:00 PM
[No subject] - by Texasrocker - 07-01-2008, 01:21 AM
[No subject] - by justlrnin - 07-01-2008, 07:41 AM
[No subject] - by Ron Ramirez - 07-03-2008, 10:28 AM
[No subject] - by etech - 07-03-2008, 09:00 PM
[No subject] - by Guest - 07-04-2008, 01:46 PM
[No subject] - by etech - 07-04-2008, 06:07 PM
[No subject] - by Ron Ramirez - 07-04-2008, 06:57 PM
[No subject] - by BDM - 07-04-2008, 07:37 PM
[No subject] - by etech - 07-04-2008, 09:06 PM
[No subject] - by Texasrocker - 07-12-2008, 03:11 AM
[No subject] - by etech - 07-12-2008, 09:50 AM
[No subject] - by justlrnin - 07-14-2008, 06:36 PM
[No subject] - by FStephenMasek - 07-14-2008, 06:50 PM
[No subject] - by exray - 07-14-2008, 08:57 PM
[No subject] - by etech - 07-14-2008, 09:27 PM
[No subject] - by BDM - 07-15-2008, 12:41 AM
[No subject] - by exray - 07-15-2008, 02:47 AM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5110 online users. [Complete List]
» 2 Member(s) | 5108 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration