Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

39-25 Project
#12

I'm in the process of taking the rust off the chassis and in the course of doing so I may lose the markings on the chassis.  I'll recreate these later if need be, but was curious.  Ron, or anyone, do you know what the "2-2" or perhaps its just "22" means on this 39-25?
[Image: https://www.dropbox.com/s/az74c5psnbgrwp....jpg?raw=1]


Messages In This Thread
39-25 Project - by klondike98 - 02-07-2014, 12:11 AM
RE: 39-25 Project - by tab10672 - 02-07-2014, 12:14 AM
RE: 39-25 Project - by morzh - 02-07-2014, 10:56 AM
RE: 39-25 Project - by klondike98 - 02-07-2014, 11:36 AM
RE: 39-25 Project - by klondike98 - 02-20-2014, 10:40 AM
RE: 39-25 Project - by Tom Hamilton - 02-25-2014, 12:57 PM
RE: 39-25 Project - by klondike98 - 02-25-2014, 02:08 PM
RE: 39-25 Project - by klondike98 - 02-25-2014, 02:53 PM
RE: 39-25 Project - by Tom Hamilton - 02-25-2014, 07:22 PM
RE: 39-25 Project - by shaler78 - 02-25-2014, 08:42 PM
RE: 39-25 Project - by klondike98 - 02-25-2014, 11:17 PM
RE: 39-25 Project - by klondike98 - 03-08-2014, 11:07 PM
RE: 39-25 Project - by Ron Ramirez - 03-09-2014, 12:14 AM
RE: 39-25 Project - by klondike98 - 03-09-2014, 08:30 AM
RE: 39-25 Project - by Joeztech - 03-23-2014, 04:12 PM
RE: 39-25 Project - by klondike98 - 03-23-2014, 04:48 PM
RE: 39-25 Project - by morzh - 03-23-2014, 06:10 PM
RE: 39-25 Project - by klondike98 - 03-23-2014, 06:27 PM
RE: 39-25 Project - by OldRestorer - 03-23-2014, 09:38 PM
RE: 39-25 Project - by klondike98 - 03-25-2014, 02:04 PM
RE: 39-25 Project - by Chuck Schwark - 03-25-2014, 02:21 PM
RE: 39-25 Project - by klondike98 - 03-25-2014, 02:34 PM
RE: 39-25 Project - by Tom Hamilton - 03-26-2014, 01:51 AM
RE: 39-25 Project - by klondike98 - 07-15-2014, 07:27 PM
RE: 39-25 Project - by klondike98 - 07-15-2014, 07:50 PM
RE: 39-25 Project - by morzh - 07-15-2014, 09:09 PM
RE: 39-25 Project - by klondike98 - 07-16-2014, 10:43 AM
RE: 39-25 Project - by morzh - 07-16-2014, 03:57 PM
RE: 39-25 Project - by klondike98 - 07-16-2014, 08:22 PM
RE: 39-25 Project - by klondike98 - 07-21-2014, 12:26 PM
RE: 39-25 Project - by Radioroslyn - 07-21-2014, 01:18 PM
RE: 39-25 Project - by klondike98 - 07-21-2014, 05:27 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM

[-]
Who's Online
There are currently 1909 online users. [Complete List]
» 3 Member(s) | 1906 Guest(s)
AvatarAvatarAvatar

>