Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

useing Correct color for Radio
#1

Here is a pic of my 47-1230 I have been refinishing. I think I have the lighter color correct on the Radio but I'm not sure on he darker color that goes on the trim, etc. On the picture I have below the Radio a piece of wood with a Dark American Walnut stain on it but it doesn't look quite right to me. I am hoping to get some of the Expert opinions here on the forum about the color is right before I spray it on the Radio and whether the Radio looks good so far to you. Thanks for any input. Warren

[Image: http://i1348.photobucket.com/albums/p721...2b39af.jpg]


Messages In This Thread
useing Correct color for Radio - by Warren - 03-09-2014, 04:59 PM
RE: useing Correct color for Radio - by morzh - 03-09-2014, 07:11 PM
RE: useing Correct color for Radio - by Warren - 03-09-2014, 07:31 PM
RE: useing Correct color for Radio - by Warren - 03-09-2014, 10:06 PM
RE: useing Correct color for Radio - by Warren - 03-09-2014, 10:55 PM
RE: useing Correct color for Radio - by morzh - 03-10-2014, 09:29 AM
RE: useing Correct color for Radio - by Jamie - 03-10-2014, 01:19 PM
RE: useing Correct color for Radio - by morzh - 03-10-2014, 02:33 PM
RE: useing Correct color for Radio - by Warren - 03-10-2014, 04:51 PM
RE: useing Correct color for Radio - by Warren - 03-15-2014, 06:27 PM
RE: useing Correct color for Radio - by morzh - 03-15-2014, 08:07 PM
RE: useing Correct color for Radio - by Warren - 03-15-2014, 10:25 PM
RE: useing Correct color for Radio - by gregb - 03-15-2014, 10:34 PM
RE: useing Correct color for Radio - by TheBakery - 04-28-2014, 01:39 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3048 online users. [Complete List]
» 2 Member(s) | 3046 Guest(s)
AvatarAvatar

>