Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Starting on the HP200CD oscilaltor
#26

I did, when I first started swapping tubes I swapped all. 6SH7 did not have any effect.

Also one thing: the chassis says 6AU5GT or 6AV5GA. I have 6AV5GT. Which are the same electrically but are in the smaller envelope I believe than GA.

I think I go buy a pair of either one recommended on the chassis and give it a try.

PS. Bought 6AU5GT, with shipping about 4 bucks a tube BIN.


Messages In This Thread
Starting on the HP200CD oscilaltor - by morzh - 02-23-2014, 09:23 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-23-2014, 10:28 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-23-2014, 11:10 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-24-2014, 09:20 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-24-2014, 09:27 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-25-2014, 11:15 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-26-2014, 10:59 AM
RE: Starting on the HP200CD oscilaltor - by morzh - 02-26-2014, 11:04 AM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-01-2014, 10:14 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-08-2014, 09:20 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-08-2014, 09:24 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-09-2014, 10:59 AM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-09-2014, 02:49 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-09-2014, 03:33 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-09-2014, 04:36 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-09-2014, 07:04 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-14-2014, 06:59 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-14-2014, 10:07 PM
RE: Starting on the HP200CD oscilaltor - by morzh - 03-15-2014, 07:46 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>