48-460 squeal

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

48-460 squeal

Jamie
Phorum Expert

Posts: 761
Threads: 56
Joined: Jul 2013
City: Kentucky

#15

03-21-2014, 10:37 AM

Hippos usually have rubber wiring. Did you replace any wires, or cover them with heat shrink? If so, check the routing of the wires. Sometimes solving a squeal is as simple as moving a wire 1/4 inch. If this isn't the trouble, i think your alignment might be a little too "hot". Like Chuck said, un-align it a little and see if the squeal stops.

The artist formerly known as Puhpow! 8)

Find

« Next Oldest | Next Newest »

Messages In This Thread

48-460 squeal - by Eric Adams - 03-20-2014, 01:16 AM

RE: 48-460 squeal - by murf - 03-20-2014, 06:42 AM

RE: 48-460 squeal - by Ron Ramirez - 03-20-2014, 08:29 AM

RE: 48-460 squeal - by Chuck Schwark - 03-20-2014, 09:07 AM

RE: 48-460 squeal - by Eric Adams - 03-20-2014, 09:28 AM

RE: 48-460 squeal - by morzh - 03-20-2014, 10:48 AM

RE: 48-460 squeal - by Eric Adams - 03-20-2014, 10:57 AM

RE: 48-460 squeal - by Eric Adams - 03-20-2014, 11:32 AM

RE: 48-460 squeal - by morzh - 03-20-2014, 01:27 PM

RE: 48-460 squeal - by Eric Adams - 03-20-2014, 07:10 PM

RE: 48-460 squeal - by morzh - 03-20-2014, 07:51 PM

RE: 48-460 squeal - by Eric Adams - 03-20-2014, 08:41 PM

RE: 48-460 squeal - by morzh - 03-20-2014, 09:55 PM

RE: 48-460 squeal - by Eric Adams - 03-21-2014, 10:09 AM

RE: 48-460 squeal - by Jamie - 03-21-2014, 10:37 AM

RE: 48-460 squeal - by Eric Adams - 03-21-2014, 06:32 PM

RE: 48-460 squeal - by Jamie - 03-22-2014, 04:45 PM

RE: 48-460 squeal - by morzh - 03-22-2014, 05:01 PM

RE: 48-460 squeal - by Eric Adams - 03-22-2014, 05:24 PM

RE: 48-460 squeal - by Jamie - 03-22-2014, 06:01 PM

RE: 48-460 squeal - by morzh - 03-22-2014, 06:27 PM

RE: 48-460 squeal - by Jamie - 03-22-2014, 09:06 PM

RE: 48-460 squeal - by morzh - 03-22-2014, 09:24 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural....morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM

Who's Online

There are currently 6343 online users. [Complete List]
» 1 Member(s) | 6342 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me