1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Starting a Philco 60 chassis restore
morzh
Odobenus rosmarus
******
Posts: 16,577
Threads: 574
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#2

03-24-2014, 04:37 PM
About grommets: every time I need one I measure where they go and how high I need them and just go to Lowe's. If I have an old one - even better.
Almost always I could get what I need, even if it is a combo of a grommet and a rubber washer to pad it if the thickness is not enough.

Then of coures there is Mark, there is the Renovated Radios.
Knobs are possibly reproduced, but you could start asking here: at least one person here deals in knobs - Mike Koste and his Gobs of Knobs, again, Mark Oppat, Julie McCall.

Go to Home Page and choose Resources, they are all there.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Starting a Philco 60 chassis restore - by morzh - 03-24-2014, 04:37 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 37-116 Cabinet Repair
It looks to me like the structure under the veneer may have expanded from humidity cracking the veneer on the surface. W...Arran — 09:42 PM
Help with Supreme 599
Iam only getting 4vac out of the tranny For the 80 filament. The line rheostat Looks fine and the tranny is getting 11...daveone23 — 08:45 PM
Rogers Majestic R-646
Transformers rewind? It's very easy! If you don't have round eyes  8-) Vlad95 — 01:55 PM
Help with Supreme 599
I found a broken wire from the end og the 300 ohm line adjust to the transforner but i dont think its needed. The transf...daveone23 — 11:43 AM
Philco 38-10 Tuning Condenser
RodB I have been using pure Vaseline for a long time for thick lubrication of home radio devices. The main reason is t...Vlad95 — 10:58 AM
Philco 38-10 Tuning Condenser
Vlad, your comment about Vaseline brought a thought. Does anyone know the long term affect on using silicon grease on t...RodB — 10:34 AM
Philco 42-345 Restoration/Repair
Arran, didn't notice the specifics for the caps. What's the code going to get me? I'm working on restoring a Philco 50-9...RodB — 10:26 AM
Philco 38-10 Tuning Condenser
I managed to get the gears lined up and the springs back in. Much easier than it thought. Putting a thin wire down insid...dconant — 09:52 AM
Philco 42-345 Restoration/Repair
Rod, Mrfixr55 and everyone else thank you very much for all your help with this radio thus far. Today will be more testi...osanders0311 — 09:26 AM
Philco 38-10 Tuning Condenser
Thanks for the reply Vlad95. I can't even see the balls let along try to remove them. The grounding forks are going to p...dconant — 08:03 AM

[-]
Who's Online
There are currently 762 online users. [Complete List]
» 1 Member(s) | 761 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration