Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Scott 800B
#10

Right you are, Brenda!!!! Both chassis are VERY heavy!!!

I installed MANY felt pads under the cabinet feet in order to slide it over the hardwood floor, which in the pic is hidden under my 111 pound Chinese dog Yogi and his quilt.

Moving the set on hardwood floors is just difficult now. Originally I was going to have the set in my bedroom, but moving it across the rug in my room might prove to be my un-doing.

Brenda: the chassis is nice looking to the point that you might want to consider having it sitting exposed on top of some kind of speaker cabinet.


Messages In This Thread
Scott 800B - by TA Forbes - 03-25-2014, 09:59 AM
RE: Scott 800B - by BrendaAnnD - 03-25-2014, 10:05 AM
RE: Scott 800B - by y2kbruce - 03-25-2014, 11:38 AM
RE: Scott 800B - by morzh - 03-25-2014, 01:37 PM
RE: Scott 800B - by TA Forbes - 03-25-2014, 02:17 PM
RE: Scott 800B - by morzh - 03-25-2014, 02:46 PM
RE: Scott 800B - by jerryhawthorne - 03-25-2014, 03:13 PM
RE: Scott 800B - by Jayce - 03-25-2014, 08:42 PM
RE: Scott 800B - by BrendaAnnD - 03-25-2014, 11:13 PM
RE: Scott 800B - by TA Forbes - 03-26-2014, 12:03 PM
RE: Scott 800B - by Jayce - 03-26-2014, 01:15 PM
RE: Scott 800B - by y2kbruce - 03-26-2014, 02:49 PM
RE: Scott 800B - by Ron Ramirez - 03-29-2014, 10:06 AM
RE: Scott 800B - by murf - 04-21-2014, 06:04 PM
RE: Scott 800B - by rocklandman - 04-22-2014, 01:44 PM
RE: Scott 800B - by PhilcoJohn - 04-24-2014, 07:15 PM
RE: Scott 800B - by TA Forbes - 04-25-2014, 10:56 AM
RE: Scott 800B - by Eliot Ness - 04-25-2014, 01:57 PM
RE: Scott 800B - by y2kbruce - 04-25-2014, 04:26 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM

[-]
Who's Online
There are currently 1355 online users. [Complete List]
» 2 Member(s) | 1353 Guest(s)
AvatarAvatar

>