Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-690 tweeter improvement
#12

Ron Ramirez Wrote:Hi Dave

A properly restored 38-690 should deliver deep bass and noticeable treble - with the bass control set to max, and the Fidelity-Selectivity control set to maximum fidelity.

And, yes, a properly restored 38-690 will, most definitely, put any lower tube count set to shame, without a doubt.

I've owned one in the past...and had a few pass through here as repair jobs...so I know how they should sound; quite simply, SUPERB.

Thanks Ron,

I wish I had one to compare it to. If I turn the bass up all the way up and the treble all the way it does sound good. I just never thought one would typically play set with both adj to max.


Thanks Ron,
Dave


Messages In This Thread
Re: Philco 38-690 tweeter improvement - by Syl - 07-25-2008, 11:16 AM
Re: Philco 38-690 tweeter improvement - by Syl - 07-25-2008, 09:19 PM
[No subject] - by Ron Ramirez - 07-25-2008, 10:39 PM
[No subject] - by wonderwrench - 07-25-2008, 10:52 PM
[No subject] - by Ron Ramirez - 07-25-2008, 11:49 PM
[No subject] - by Dave Slusarczyk - 07-25-2008, 11:53 PM
[No subject] - by wonderwrench - 07-26-2008, 12:06 AM
[No subject] - by Ron Ramirez - 07-26-2008, 12:06 AM
[No subject] - by Ron Ramirez - 07-26-2008, 12:13 AM
[No subject] - by Dave Slusarczyk - 07-26-2008, 12:59 AM
[No subject] - by BDM - 07-26-2008, 01:40 AM
[No subject] - by wonderwrench - 07-26-2008, 01:48 AM
[No subject] - by wonderwrench - 07-26-2008, 02:30 AM
[No subject] - by Syl - 07-26-2008, 09:33 AM
[No subject] - by Ron Ramirez - 07-26-2008, 10:20 AM
[No subject] - by Syl - 07-26-2008, 12:52 PM
[No subject] - by Dave Slusarczyk - 07-26-2008, 04:33 PM
[No subject] - by wonderwrench - 07-26-2008, 04:47 PM
[No subject] - by wonderwrench - 07-26-2008, 04:53 PM
[No subject] - by Ron Ramirez - 07-26-2008, 05:40 PM
[No subject] - by Syl - 07-26-2008, 05:51 PM
[No subject] - by Syl - 07-26-2008, 05:55 PM
[No subject] - by Dave Slusarczyk - 07-26-2008, 06:50 PM
[No subject] - by Syl - 07-26-2008, 08:17 PM
[No subject] - by Dave Slusarczyk - 07-26-2008, 10:26 PM
[No subject] - by Syl - 07-27-2008, 12:11 AM
[No subject] - by Dave Slusarczyk - 07-27-2008, 02:02 PM
[No subject] - by Terry Judkins - 07-27-2008, 06:59 PM
[No subject] - by wonderwrench - 07-27-2008, 07:11 PM
[No subject] - by Dave Slusarczyk - 07-27-2008, 07:53 PM
[No subject] - by wonderwrench - 07-27-2008, 10:00 PM
[No subject] - by Syl - 07-28-2008, 11:21 AM
[No subject] - by Dave Slusarczyk - 07-28-2008, 06:10 PM
[No subject] - by BDM - 07-28-2008, 06:17 PM
[No subject] - by Ron Ramirez - 07-28-2008, 06:59 PM
[No subject] - by Dave Slusarczyk - 07-28-2008, 07:12 PM
[No subject] - by Syl - 07-28-2008, 09:33 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>