1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
A Beginner's Journey: The Philco 40-190
DeckApe
Senior Member
****
Posts: 438
Threads: 15
Joined: Jul 2008
City: Anacortes, WA
#18

07-29-2008, 12:20 PM
Good morning, all!

Here's the speaker in question:

[Image: http://i261.photobucket.com/albums/ii66/...CF0022.jpg]
As you can see, the cone is hashed well beyond Syl's $1 method (or even using coffee filters to reinforce it)...

[Image: http://i261.photobucket.com/albums/ii66/...CF0021.jpg]

The frame is 12", edge to edge. The hole in the disintegrating plywood is 11" edge to edge.

The part number is buried under the rust, but (edit) I can make out a "K." The frame is stamped near the connector with "81220." (I'm a little iffy on the eight... top half buried in rust again.) I just removed the speaker from the board and spotted either "B-2" or "8-2" stamped on the back side of the cone.

Unless the 36-1479-2 looks vastly different from the '-4, I don't think I have the correct speaker.

By the way, what IS the diff betwen the 36-1479-2 and -4?
Find
« Next Oldest | Next Newest »


Messages In This Thread
[No subject] - by DeckApe - 07-07-2008, 03:39 PM
[No subject] - by Ron Ramirez - 07-07-2008, 09:45 PM
[No subject] - by DeckApe - 07-08-2008, 07:27 PM
[No subject] - by Michael Dennis - 07-08-2008, 10:14 PM
[No subject] - by DeckApe - 07-09-2008, 12:24 AM
[No subject] - by Michael Dennis - 07-09-2008, 07:05 AM
[No subject] - by DeckApe - 07-17-2008, 12:46 AM
[No subject] - by gary rabbitt - 07-17-2008, 03:04 AM
[No subject] - by DeckApe - 07-17-2008, 11:57 AM
[No subject] - by DeckApe - 07-18-2008, 11:28 PM
[No subject] - by DeckApe - 07-21-2008, 12:38 PM
[No subject] - by DeckApe - 07-24-2008, 11:17 PM
[No subject] - by DeckApe - 07-27-2008, 09:29 PM
[No subject] - by DeckApe - 07-29-2008, 01:16 AM
[No subject] - by BDM - 07-29-2008, 08:56 AM
[No subject] - by DeckApe - 07-29-2008, 12:20 PM
[No subject] - by DeckApe - 08-14-2008, 01:09 AM
[No subject] - by DeckApe - 08-14-2008, 11:48 AM
[No subject] - by Ron Ramirez - 08-14-2008, 10:37 PM
[No subject] - by DeckApe - 08-15-2008, 08:04 AM
[No subject] - by Ron Ramirez - 08-15-2008, 05:30 PM
[No subject] - by DeckApe - 08-16-2008, 03:38 PM
[No subject] - by Ron Ramirez - 08-16-2008, 04:17 PM
[No subject] - by DeckApe - 08-16-2008, 05:02 PM
[No subject] - by DeckApe - 08-21-2008, 01:08 AM
Re: - by Chuck Schwark - 09-07-2008, 10:49 PM
Re: A Beginner's Journey: The Philco 40-190 - by Guest - 09-16-2008, 08:30 PM
Re: A Beginner's Journey: The Philco 40-190 - by Guest - 03-28-2010, 04:08 PM



Users browsing this thread: 14 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5734 online users. [Complete List]
» 1 Member(s) | 5733 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration