1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
42-380 escutcheon related
gfleduc
Junior Member
**
Posts: 8
Threads: 2
Joined: Feb 2014
City: Kingwood Texas
#7

04-28-2014, 10:42 PM
Using a reproduction escutcheon one has to transfer or replace the white vellum paper and angled metal piece on the back. When doing mine, I found one of the four drive screws was missing.
The drive screws are tiny ~ 1/16” dia x 3/16” long.

Replacement screws can be purchased @ SpencerAircraft.com
P/N MS21318-2 or alt part # AN535-00-3

I have now have extras if you need one.
FYI – install hole = .052 diameter, that is a #55 drill


   
(This post was last modified: 04-28-2014, 11:12 PM by gfleduc.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
42-380 escutcheon related - by gfleduc - 03-03-2014, 11:23 PM
RE: 42-380 escutcheon related - by Eric T - 03-04-2014, 09:33 AM
RE: 42-380 escutcheon related - by Ron Ramirez - 03-04-2014, 11:28 AM
RE: 42-380 escutcheon related - by gfleduc - 03-06-2014, 12:07 AM
RE: 42-380 escutcheon related - by gfleduc - 03-24-2014, 12:02 PM
RE: 42-380 escutcheon related - by gfleduc - 04-26-2014, 06:05 PM
RE: 42-380 escutcheon related - by gfleduc - 04-28-2014, 10:42 PM
RE: 42-380 escutcheon related - by Radioroslyn - 08-12-2016, 01:57 PM
RE: 42-380 escutcheon related - by klondike98 - 08-12-2016, 02:39 PM
RE: 42-380 escutcheon related - by Warren - 08-15-2016, 06:39 PM
RE: 42-380 escutcheon related - by Radioroslyn - 08-16-2016, 12:59 PM
RE: 42-380 escutcheon related - by klondike98 - 08-15-2016, 02:56 PM
RE: 42-380 escutcheon related - by Radioroslyn - 08-15-2016, 08:01 PM
RE: 42-380 escutcheon related - by sam - 08-15-2016, 10:49 PM
RE: 42-380 escutcheon related - by Radioroslyn - 08-15-2016, 10:54 PM
RE: 42-380 escutcheon related - by sam - 08-16-2016, 01:07 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4414 online users. [Complete List]
» 1 Member(s) | 4413 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration