Chassis Detailing or not

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Chassis Detailing or not

codefox1
Silent Key

Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY

#16

05-11-2014, 09:34 AM

I like to get rid of deep rust and pitting from "guests" or leaking capacitors by steel wool or abrasive stones, and as said already, some similar colored paint in the affected area(s.) If a chassis is totally stripped (as in repurposing an old organ amp into a guitar amp,) I'll shine it up or paint it as needed.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Chassis Detailing or not - by 462ron - 05-09-2014, 09:00 PM

RE: Chassis Detailing or not - by 37silverstreak - 05-09-2014, 09:22 PM

RE: Chassis Detailing or not - by Ron Ramirez - 05-09-2014, 09:57 PM

RE: Chassis Detailing or not - by gregb - 05-09-2014, 11:06 PM

RE: Chassis Detailing or not - by 462ron - 05-10-2014, 12:55 AM

RE: Chassis Detailing or not - by Eric Adams - 05-10-2014, 10:46 AM

RE: Chassis Detailing or not - by Mondial - 05-10-2014, 11:04 AM

RE: Chassis Detailing or not - by OldRestorer - 05-10-2014, 08:58 PM

RE: Chassis Detailing or not - by exray - 05-10-2014, 09:49 PM

RE: Chassis Detailing or not - by gregb - 05-10-2014, 11:44 PM

RE: Chassis Detailing or not - by Eric Adams - 05-10-2014, 11:51 PM

RE: Chassis Detailing or not - by gregb - 05-11-2014, 12:03 AM

RE: Chassis Detailing or not - by Arran - 05-11-2014, 12:09 AM

RE: Chassis Detailing or not - by Warren - 05-11-2014, 02:40 AM

RE: Chassis Detailing or not - by PhilcoJohn - 05-11-2014, 07:56 AM

RE: Chassis Detailing or not - by codefox1 - 05-11-2014, 09:34 AM

RE: Chassis Detailing or not - by gregb - 05-11-2014, 10:56 AM

RE: Chassis Detailing or not - by Groundhog74 - 05-11-2014, 06:06 PM

RE: Chassis Detailing or not - by 462ron - 05-11-2014, 06:43 PM

RE: Chassis Detailing or not - by Warren - 05-12-2014, 01:30 AM

RE: Chassis Detailing or not - by codefox1 - 05-12-2014, 11:33 AM

RE: Chassis Detailing or not - by gregb - 05-12-2014, 11:47 AM

RE: Chassis Detailing or not - by Warren - 05-12-2014, 02:35 PM

RE: Chassis Detailing or not - by Jamie - 05-12-2014, 04:26 PM

View a Printable Version

Users browsing this thread: 11 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 6149 online users. [Complete List]
» 4 Member(s) | 6145 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me