Chassis Detailing or not

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Chassis Detailing or not

Groundhog74
Member

Posts: 227
Threads: 60
Joined: Sep 2012
City: Kokomo, Indiana

#18

05-11-2014, 06:06 PM

I painted one chassis. A philco 90. Only because it was totally filthy and severely rusted in some areas where some unknown substance, that vaguely smelled like bar-b-que grill grease, had been spilled all over it (and the cabinet). Hated to do it, but it would have been hideous otherwise. All the others I clean as well as I can and polish anything that's easily polished.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Chassis Detailing or not - by 462ron - 05-09-2014, 09:00 PM

RE: Chassis Detailing or not - by 37silverstreak - 05-09-2014, 09:22 PM

RE: Chassis Detailing or not - by Ron Ramirez - 05-09-2014, 09:57 PM

RE: Chassis Detailing or not - by gregb - 05-09-2014, 11:06 PM

RE: Chassis Detailing or not - by 462ron - 05-10-2014, 12:55 AM

RE: Chassis Detailing or not - by Eric Adams - 05-10-2014, 10:46 AM

RE: Chassis Detailing or not - by Mondial - 05-10-2014, 11:04 AM

RE: Chassis Detailing or not - by OldRestorer - 05-10-2014, 08:58 PM

RE: Chassis Detailing or not - by exray - 05-10-2014, 09:49 PM

RE: Chassis Detailing or not - by gregb - 05-10-2014, 11:44 PM

RE: Chassis Detailing or not - by Eric Adams - 05-10-2014, 11:51 PM

RE: Chassis Detailing or not - by gregb - 05-11-2014, 12:03 AM

RE: Chassis Detailing or not - by Arran - 05-11-2014, 12:09 AM

RE: Chassis Detailing or not - by Warren - 05-11-2014, 02:40 AM

RE: Chassis Detailing or not - by PhilcoJohn - 05-11-2014, 07:56 AM

RE: Chassis Detailing or not - by codefox1 - 05-11-2014, 09:34 AM

RE: Chassis Detailing or not - by gregb - 05-11-2014, 10:56 AM

RE: Chassis Detailing or not - by Groundhog74 - 05-11-2014, 06:06 PM

RE: Chassis Detailing or not - by 462ron - 05-11-2014, 06:43 PM

RE: Chassis Detailing or not - by Warren - 05-12-2014, 01:30 AM

RE: Chassis Detailing or not - by codefox1 - 05-12-2014, 11:33 AM

RE: Chassis Detailing or not - by gregb - 05-12-2014, 11:47 AM

RE: Chassis Detailing or not - by Warren - 05-12-2014, 02:35 PM

RE: Chassis Detailing or not - by Jamie - 05-12-2014, 04:26 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 6469 online users. [Complete List]
» 1 Member(s) | 6468 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me