Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Chassis Detailing or not
#20

Greg, I agree by the time you are finished steel wool, buffing up, etc the original finish is off. So, to make sure you can paint as you said. Although I am not sure that the chassis will be prone to more rust, etc if it is kept in a clean dry environment. For something to rust it has to have both moisture and oxygen on it, I may be wrong but it seems if it is kept in the house it wont get much moisture.. maybe depends on the climate also even in the house. That being said I do prefer to keep a chassis as close to the way it was made originally as possible too.


Messages In This Thread
Chassis Detailing or not - by 462ron - 05-09-2014, 09:00 PM
RE: Chassis Detailing or not - by 37silverstreak - 05-09-2014, 09:22 PM
RE: Chassis Detailing or not - by Ron Ramirez - 05-09-2014, 09:57 PM
RE: Chassis Detailing or not - by gregb - 05-09-2014, 11:06 PM
RE: Chassis Detailing or not - by 462ron - 05-10-2014, 12:55 AM
RE: Chassis Detailing or not - by Eric Adams - 05-10-2014, 10:46 AM
RE: Chassis Detailing or not - by Mondial - 05-10-2014, 11:04 AM
RE: Chassis Detailing or not - by OldRestorer - 05-10-2014, 08:58 PM
RE: Chassis Detailing or not - by exray - 05-10-2014, 09:49 PM
RE: Chassis Detailing or not - by gregb - 05-10-2014, 11:44 PM
RE: Chassis Detailing or not - by Eric Adams - 05-10-2014, 11:51 PM
RE: Chassis Detailing or not - by gregb - 05-11-2014, 12:03 AM
RE: Chassis Detailing or not - by Arran - 05-11-2014, 12:09 AM
RE: Chassis Detailing or not - by Warren - 05-11-2014, 02:40 AM
RE: Chassis Detailing or not - by PhilcoJohn - 05-11-2014, 07:56 AM
RE: Chassis Detailing or not - by codefox1 - 05-11-2014, 09:34 AM
RE: Chassis Detailing or not - by gregb - 05-11-2014, 10:56 AM
RE: Chassis Detailing or not - by Groundhog74 - 05-11-2014, 06:06 PM
RE: Chassis Detailing or not - by 462ron - 05-11-2014, 06:43 PM
RE: Chassis Detailing or not - by Warren - 05-12-2014, 01:30 AM
RE: Chassis Detailing or not - by codefox1 - 05-12-2014, 11:33 AM
RE: Chassis Detailing or not - by gregb - 05-12-2014, 11:47 AM
RE: Chassis Detailing or not - by Warren - 05-12-2014, 02:35 PM
RE: Chassis Detailing or not - by Jamie - 05-12-2014, 04:26 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6717 online users. [Complete List]
» 1 Member(s) | 6716 Guest(s)
Avatar

>