To restore or not to restore?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

To restore or not to restore?

Arran
Phorum Expert

Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

#9

05-24-2014, 03:12 AM

Try some alcohol on it, they may have slobbed shellac all over the original lacquer. You really have nothing to loose by trying it, I had a radio with a blotchy yellowish look, even after the Gojo treatment, tried some rubbing alcohol on it and it came off revealing the original finish underneath.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

To restore or not to restore? - by OldRestorer - 05-23-2014, 01:01 PM

RE: To restore or not to restore? - by morzh - 05-23-2014, 01:17 PM

RE: To restore or not to restore? - by Chuck Schwark - 05-23-2014, 01:55 PM

RE: To restore or not to restore? - by tab10672 - 05-23-2014, 02:27 PM

RE: To restore or not to restore? - by morzh - 05-23-2014, 02:27 PM

RE: To restore or not to restore? - by OldRestorer - 05-23-2014, 02:57 PM

RE: To restore or not to restore? - by radiohenry - 05-23-2014, 04:11 PM

RE: To restore or not to restore? - by OldRestorer - 05-23-2014, 05:54 PM

RE: To restore or not to restore? - by Arran - 05-24-2014, 03:12 AM

RE: To restore or not to restore? - by OldRestorer - 05-24-2014, 09:12 AM

RE: To restore or not to restore? - by PAradiogeek - 05-24-2014, 11:01 AM

RE: To restore or not to restore? - by codefox1 - 05-25-2014, 07:07 PM

RE: To restore or not to restore? - by OldRestorer - 05-26-2014, 07:37 AM

RE: To restore or not to restore? - by Steve Davis - 05-26-2014, 08:00 AM

RE: To restore or not to restore? - by OldRestorer - 05-26-2014, 08:27 AM

RE: To restore or not to restore? - by radiohenry - 05-26-2014, 11:06 AM

RE: To restore or not to restore? - by Eliot Ness - 05-26-2014, 01:40 PM

RE: To restore or not to restore? - by radiohenry - 05-26-2014, 02:28 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 4645 online users. [Complete List]
» 3 Member(s) | 4642 Guest(s)