Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco K type Speaker ID problem
#1

I am trying to sort out what Output Transformers were used in each model Radio.

I have found Philco charts that are partially helpful

My Task Find correct Philco P/N for each Speaker Output Coil

Also what does the J mean tacked on some of the OT P/N ?


Speaker for the Model 20 Cathedral (So far it is 2766) IN FACT marked 2766J SAME AS 90 ??

Speaker for the Model 90 Cathedral with PP 47 tubes (So far 2635) In fact marked 2635J
This is also shown as for the Models 90B.G. 90X and 490

Speaker for the Model 90 Cathedral with PP 45 Tubes (So far same as Model 20 2766)

Now a Chart from Philco lists
Model 70 with single 47 P/N 2673
Model 90 with dual 45 P/N 2766
Model 20 not listed on this chart.

NOW I am assuming these are for the Cathedral Speakers, as I see the Model 70 and 90 Consoles using PP 45/47 Tubes uses a larger OT.

I am confused and any help trying to correctly ID OT for Philco Models
20-70-90 both Cathedral and console.

I have in my possession Speakers from a 70 Console and a 90 Console using PP, If I decide to take these apart I can them ID the coils hopefully

I also have 5 Cathedral Speakers in need of Cones and or OT
2 of these are from a Model 20 Chassis and both OT are marked 2766J (J ?)

Bob T


Messages In This Thread
Philco K type Speaker ID problem - by joybird - 05-27-2014, 03:28 PM
RE: Philco K type Speaker ID problem - by joybird - 05-27-2014, 06:49 PM



Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2369 online users. [Complete List]
» 1 Member(s) | 2368 Guest(s)
Avatar

>