Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco D-10 needle source
#7

You guys must be referring to that "Dynamic" cartridge Philco came out with right after WWII. Yes, the styli for those are basically unobtainium. To make matters worse, Philco designed the cartridge to only accept Philco's own proprietary stylus; use of a steel needle or the generic sapphire needle will destroy the cone of the cartridge which the stylus slips into.

A newer magnetic cartridge would seem to be an answer to the problem, until you consider that Philco set the mounting holes too far back for a modern cartridge.

Sometimes companies did some really dumb things in order to be different from their competitors...but then again, Philco didn't expect anyone to still be using 46-1209 sets 68 years later.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco D-10 needle source - by brownie45 - 05-28-2014, 08:37 AM
RE: Philco D-10 needle source - by TA Forbes - 05-28-2014, 10:50 AM
RE: Philco D-10 needle source - by brownie45 - 05-28-2014, 12:48 PM
RE: Philco D-10 needle source - by sam - 05-28-2014, 01:18 PM
RE: Philco D-10 needle source - by Warren - 05-28-2014, 01:56 PM
RE: Philco D-10 needle source - by TA Forbes - 05-28-2014, 11:17 PM
RE: Philco D-10 needle source - by Ron Ramirez - 05-29-2014, 05:42 AM
RE: Philco D-10 needle source - by brownie45 - 05-29-2014, 06:58 AM
RE: Philco D-10 needle source - by Randy H. - 06-09-2014, 07:11 PM
RE: Philco D-10 needle source - by Ron Ramirez - 06-09-2014, 08:18 PM
RE: Philco D-10 needle source - by brownie45 - 06-09-2014, 09:39 PM
RE: Philco D-10 needle source - by Randy H. - 06-13-2014, 05:46 PM
RE: Philco D-10 needle source - by Ron Ramirez - 06-13-2014, 06:00 PM
RE: Philco D-10 needle source - by Skip - 06-13-2014, 06:11 PM
RE: Philco D-10 needle source - by Warren - 06-13-2014, 10:22 PM
RE: Philco D-10 needle source - by w4rtc - 06-14-2014, 07:53 AM
RE: Philco D-10 needle source - by brownie45 - 06-15-2014, 12:24 PM
RE: Philco D-10 needle source - by w4rtc - 06-15-2014, 05:01 PM
RE: Philco D-10 needle source - by brownie45 - 06-15-2014, 07:02 PM
RE: Philco D-10 needle source - by Warren - 06-15-2014, 08:29 PM
RE: Philco D-10 needle source - by w4rtc - 06-15-2014, 11:22 PM
RE: Philco D-10 needle source - by Warren - 06-16-2014, 01:53 AM
RE: Philco D-10 needle source - by w4rtc - 06-16-2014, 10:35 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>