1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
39-7 restore
Nick3092
Member
***
Posts: 126
Threads: 13
Joined: Sep 2013
City: Milwaukee, Wisconsin
#7

06-05-2014, 11:58 PM
My 39-6 (which is the same minus the push buttons) was the same. I just let it crumble off the transformer wires and put colored heat shrink over it. Worked well.
Find
« Next Oldest | Next Newest »


Messages In This Thread
39-7 restore - by bfrohwein - 06-02-2014, 12:20 PM
RE: 39-7 restore - by bfrohwein - 06-02-2014, 06:56 PM
RE: 39-7 restore - by bfrohwein - 06-05-2014, 01:27 AM
RE: 39-7 restore - by Eliot Ness - 06-05-2014, 07:46 AM
RE: 39-7 restore - by bfrohwein - 06-05-2014, 10:16 AM
RE: 39-7 restore - by morzh - 06-05-2014, 10:40 AM
RE: 39-7 restore - by Nick3092 - 06-05-2014, 11:58 PM
RE: 39-7 restore - by Arran - 06-06-2014, 12:22 AM
RE: 39-7 restore - by bfrohwein - 06-06-2014, 04:10 PM
RE: 39-7 restore - by David - 06-07-2014, 03:31 PM
RE: 39-7 restore - by bfrohwein - 06-07-2014, 04:02 PM
RE: 39-7 restore - by Ron Ramirez - 06-07-2014, 10:42 PM
RE: 39-7 restore - by bfrohwein - 06-20-2014, 12:40 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration