philco bakelite blocks

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

philco bakelite blocks

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

12-08-2005, 10:44 PM

Tubenutt...can't you use the X/Y safety caps in the block? I do...mine come from Mouser, and look like ceramic discs except they are blue. I use .01 uF, and they fit.

I've never bought anything from Just Radios - nothing against them, I'm just used to buying from Mouser and Allied - so I don't know how big the Just Radios X/Y safety caps are.

Edit: The counter guy at the local electronics distributor, where I occasionally buy a few parts when I'm in a hurry, insists that a metalized film capacitor rated at 630v DC is safe to use on AC; they don't carry the X/Y caps. But I use the X/Y units anyway. Better safe than sorry, especially when they're going into radios that aren't mine (customers' sets).

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

philco bakelite blocks - by Chris Drumma - 12-04-2005, 03:40 PM

[No subject] - by Chuck Schwark - 12-04-2005, 03:54 PM

[No subject] - by Chris Drumma - 12-04-2005, 04:24 PM

[No subject] - by Ron Ramirez - 12-04-2005, 05:05 PM

[No subject] - by Poston Drake - 12-07-2005, 01:26 PM

[No subject] - by don'tdomelikethat - 12-07-2005, 07:15 PM

[No subject] - by Guest - 12-08-2005, 10:14 PM

[No subject] - by Ron Ramirez - 12-08-2005, 10:44 PM

[No subject] - by Chuck Schwark - 12-09-2005, 12:32 AM

[No subject] - by Ron Ramirez - 12-09-2005, 01:42 AM

[No subject] - by Poston Drake - 12-09-2005, 11:19 AM

[No subject] - by Ron Ramirez - 12-09-2005, 12:52 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 6186 online users. [Complete List]
» 1 Member(s) | 6185 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me