Old tubes

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Old tubes

TA Forbes
Deviate Emeritus

Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC

06-13-2014, 01:22 PM

TUBE REJUVINATION.doc Size: 78.5 KB Downloads: 189

Here is one method of tube rejuvenation. This is mainly for triodes with a thoriated filament.

Early tubes that do not respond well to this method of rejuvenation: 11, 12, 00, 26, 27, 45, 50, 80, 81, 71A

Another method is to "flash" HV across the tube filament. While I am not exactly sure how this works, I have a Knight tube tester that has been converted into this kind of rejuvenator. With it I have had success bringing back many varieties of tubes, including 75s (triode section), 78s, 80s, 45s, 6A3s, and 6L6s. FYI the 6A3 went from 1300uMho to 4600uMho, as measured on my Weston 981-3.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Old tubes - by fields 100 - 06-13-2014, 06:06 AM

RE: Old tubes - by Eliot Ness - 06-13-2014, 09:04 AM

RE: Old tubes - by fields 100 - 06-13-2014, 09:47 AM

RE: Old tubes - by TA Forbes - 06-13-2014, 01:22 PM

RE: Old tubes - by Randy H. - 06-13-2014, 03:29 PM

RE: Old tubes - by fields 100 - 06-13-2014, 06:18 PM

RE: Old tubes - by Arran - 06-14-2014, 03:32 AM

RE: Old tubes - by Randy H. - 06-16-2014, 05:08 PM

RE: Old tubes - by Phlogiston - 06-16-2014, 07:42 PM

RE: Old tubes - by Phlogiston - 06-16-2014, 08:20 PM

RE: Old tubes - by fields 100 - 06-16-2014, 08:44 PM

RE: Old tubes - by Eliot Ness - 06-17-2014, 07:35 AM

RE: Old tubes - by codefox1 - 06-18-2014, 03:34 PM

RE: Old tubes - by Phlogiston - 06-18-2014, 03:40 PM

RE: Old tubes - by Tom Hamilton - 07-12-2014, 04:22 PM

View a Printable Version

Users browsing this thread:

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me