Old tubes

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Old tubes

Arran
Phorum Expert

Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

06-14-2014, 03:32 AM

Before you attempt any sort of rejuvenation technique on a globe type tube try re-soldering the tube pins, particularly the cathode and heater pins, and the grid cap. Sometimes a tube with a bad solder joint on the grid cap will test as weak, one with a bad solder joint on the cathode will test weak or test with zero emission. On a 27 or a 26 the grid is connected to one of the small pins, the plate is connected to the other.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

Old tubes - by fields 100 - 06-13-2014, 06:06 AM

RE: Old tubes - by Eliot Ness - 06-13-2014, 09:04 AM

RE: Old tubes - by fields 100 - 06-13-2014, 09:47 AM

RE: Old tubes - by TA Forbes - 06-13-2014, 01:22 PM

RE: Old tubes - by Randy H. - 06-13-2014, 03:29 PM

RE: Old tubes - by fields 100 - 06-13-2014, 06:18 PM

RE: Old tubes - by Arran - 06-14-2014, 03:32 AM

RE: Old tubes - by Randy H. - 06-16-2014, 05:08 PM

RE: Old tubes - by Phlogiston - 06-16-2014, 07:42 PM

RE: Old tubes - by Phlogiston - 06-16-2014, 08:20 PM

RE: Old tubes - by fields 100 - 06-16-2014, 08:44 PM

RE: Old tubes - by Eliot Ness - 06-17-2014, 07:35 AM

RE: Old tubes - by codefox1 - 06-18-2014, 03:34 PM

RE: Old tubes - by Phlogiston - 06-18-2014, 03:40 PM

RE: Old tubes - by Tom Hamilton - 07-12-2014, 04:22 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online

There are currently 4383 online users. [Complete List]
» 1 Member(s) | 4382 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me