Tube schematic Pinouts

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Tube schematic Pinouts

Warren
Senior Member

Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California

06-28-2014, 01:08 AM

I have been trying to find a site that will show you tube schematics with the numbered pin outs shown but haven't had any luck. Does anyone know where I could find this info?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Tube schematic Pinouts - by Warren - 06-28-2014, 01:08 AM

RE: Tube schematic Pinouts - by Ron Ramirez - 06-28-2014, 07:18 AM

RE: Tube schematic Pinouts - by gregb - 06-28-2014, 10:32 AM

RE: Tube schematic Pinouts - by Warren - 06-28-2014, 03:25 PM

RE: Tube schematic Pinouts - by Kestas - 07-01-2014, 07:15 PM

RE: Tube schematic Pinouts - by brownie45 - 07-20-2014, 11:27 AM

RE: Tube schematic Pinouts - by morzh - 07-20-2014, 11:36 AM

RE: Tube schematic Pinouts - by Eliot Ness - 07-20-2014, 12:55 PM

RE: Tube schematic Pinouts - by Joeztech - 07-20-2014, 02:23 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM

Who's Online

There are currently 3037 online users. [Complete List]
» 1 Member(s) | 3036 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me