1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Capasitor blocks ?????
Dan Walker
Senior Member
****
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
#1

07-16-2014, 08:31 PM
I just picked up this Philco model 3650 radio ..That is the Canadian version.. the American one is 650.. The radio does work.
I am having a real challenge with those blocks.. The schematics I have are hard to read and they don't show where the blocks are
Is there a site where I can get more information about these blocks.
I need to know what caps are inside each block.
Also, are the electrolytic caps grounded to the chassis ?
Any information would be a help..
Thanks Dan


Attached Files Image(s)
   
Find
« Next Oldest | Next Newest »


Messages In This Thread
Capasitor blocks ????? - by Dan Walker - 07-16-2014, 08:31 PM
RE: Capasitor blocks ????? - by gregb - 07-16-2014, 08:39 PM
RE: Capasitor blocks ????? - by klondike98 - 07-16-2014, 08:40 PM
RE: Capasitor blocks ????? - by GarySP - 07-16-2014, 08:47 PM
RE: Capasitor blocks ????? - by Dan Walker - 07-16-2014, 09:57 PM
RE: Capasitor blocks ????? - by Warren - 07-17-2014, 12:06 AM
RE: Capasitor blocks ????? - by gregb - 07-17-2014, 12:13 AM
RE: Capasitor blocks ????? - by Dan Walker - 07-17-2014, 12:52 AM
RE: Capasitor blocks ????? - by Ron Ramirez - 07-17-2014, 05:41 AM
RE: Capasitor blocks ????? - by Warren - 07-17-2014, 02:29 PM
RE: Capasitor blocks ????? - by gregb - 07-17-2014, 02:58 PM
RE: Capasitor blocks ????? - by Ron Ramirez - 07-17-2014, 05:20 PM
RE: Capasitor blocks ????? - by exray - 07-17-2014, 06:00 PM
RE: Capasitor blocks ????? - by Ron Ramirez - 07-17-2014, 06:18 PM
RE: Capasitor blocks ????? - by Warren - 07-17-2014, 07:31 PM
RE: Capasitor blocks ????? - by exray - 07-17-2014, 09:28 PM
RE: Capasitor blocks ????? - by Ron Ramirez - 07-18-2014, 05:55 AM
RE: Capasitor blocks ????? - by brownie45 - 07-19-2014, 08:27 AM
RE: Capasitor blocks ????? - by morzh - 07-19-2014, 09:24 AM
RE: Capasitor blocks ????? - by Arran - 07-20-2014, 09:11 AM
RE: Capasitor blocks ????? - by codefox1 - 07-21-2014, 10:26 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration