Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Is it worth rebuilding?
#12

OK everyone, ran into another curve with this unit. What can anyone tell me about copper oxide rectifiers? Seems this unit has one on the VOM section, I'm presuming to rectify AC voltage before the meter. It also has what looks like a variable resistor which I would think is for calibration purposes? The whole thing is built into a standard 4 pin tube base. How would I go about testing this unit? If bad, could I rebuild it using selenium diodes? Learning as I go... Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan


Messages In This Thread
Is it worth rebuilding? - by GarySP - 07-08-2014, 09:28 AM
RE: Is it worth rebuilding? - by klondike98 - 07-08-2014, 09:37 AM
RE: Is it worth rebuilding? - by morzh - 07-08-2014, 09:43 AM
RE: Is it worth rebuilding? - by codefox1 - 07-09-2014, 09:44 PM
RE: Is it worth rebuilding? - by TA Forbes - 07-10-2014, 06:17 PM
RE: Is it worth rebuilding? - by codefox1 - 07-11-2014, 09:30 AM
RE: Is it worth rebuilding? - by brownie45 - 07-13-2014, 09:14 PM
RE: Is it worth rebuilding? - by tom.seeger - 07-13-2014, 09:34 PM
RE: Is it worth rebuilding? - by Arran - 07-14-2014, 07:28 AM
RE: Is it worth rebuilding? - by GarySP - 07-14-2014, 11:02 AM
RE: Is it worth rebuilding? - by Paul Philco322 - 07-15-2014, 09:00 PM
RE: Is it worth rebuilding? - by GarySP - 07-26-2014, 10:55 AM
RE: Is it worth rebuilding? - by GarySP - 07-26-2014, 11:03 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3157 online users. [Complete List]
» 1 Member(s) | 3156 Guest(s)
Avatar

>