Plate voltages for UV-200 tubes

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Plate voltages for UV-200 tubes

gregb
Senior Member

Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA

07-27-2014, 10:59 PM

The detector plate voltage should be 22.5 volts but you are close enough it should work. Do you have that detector B+ lead connected to the 22.5 volt terminal on the ARBEIII? If so you should be go.

Gregb

Find

« Next Oldest | Next Newest »

Messages In This Thread

Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-27-2014, 10:42 PM

RE: Plate voltages for UV200 tubes - by morzh - 07-27-2014, 10:47 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-27-2014, 10:51 PM

RE: Plate voltages for UV-200 tubes - by gregb - 07-27-2014, 10:59 PM

RE: Plate voltages for UV-200 tubes - by Mondial - 07-27-2014, 11:03 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-27-2014, 11:19 PM

RE: Plate voltages for UV-200 tubes - by gregb - 07-27-2014, 11:23 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-27-2014, 11:29 PM

RE: Plate voltages for UV-200 tubes - by gregb - 07-27-2014, 11:40 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-28-2014, 11:09 PM

RE: Plate voltages for UV-200 tubes - by Radioroslyn - 07-29-2014, 07:00 AM

RE: Plate voltages for UV-200 tubes - by Ron Ramirez - 07-29-2014, 08:15 AM

RE: Plate voltages for UV-200 tubes - by morzh - 07-29-2014, 10:20 AM

RE: Plate voltages for UV-200 tubes - by Ron Ramirez - 07-29-2014, 11:02 AM

RE: Plate voltages for UV-200 tubes - by morzh - 07-29-2014, 11:09 AM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-29-2014, 05:43 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-29-2014, 05:53 PM

RE: Plate voltages for UV-200 tubes - by gregb - 07-29-2014, 05:59 PM

RE: Plate voltages for UV-200 tubes - by Ron Ramirez - 07-29-2014, 06:07 PM

RE: Plate voltages for UV-200 tubes - by Mondial - 07-29-2014, 06:31 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-29-2014, 06:41 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-29-2014, 07:48 PM

RE: Plate voltages for UV-200 tubes - by NostalgiaRadioTime - 07-29-2014, 10:56 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

Who's Online

There are currently 4911 online users. [Complete List]
» 2 Member(s) | 4909 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me