Philco 38-7CS

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 38-7CS

Bob Andersen
Phorum Expert

Posts: 797
Threads: 42
Joined: Dec 2008
City: Chicago, IL

#20

07-28-2014, 06:51 PM

Although I had swapped out all the tubes three times, I gave it another go and viola! - it's working Icon_smile

It seems that all three of these Philco 6K7Gs have one problem or another. I'm pretty darn sure they tested good before but I'll test them again right now. The one 6K7 that's actually working well is a grungy old Zentih.

[Image: https://farm4.staticflickr.com/3841/1479...a942_c.jpg]

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:32 PM

RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:41 PM

RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:48 PM

RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 07:57 PM

RE: Philco 38-7CS - by Arran - 07-24-2014, 09:34 PM

RE: Philco 38-7CS - by Bob Andersen - 07-24-2014, 09:50 PM

RE: Philco 38-7CS - by codefox1 - 07-25-2014, 01:34 PM

RE: Philco 38-7CS - by Chuck Schwark - 07-25-2014, 01:46 PM

RE: Philco 38-7CS - by morzh - 07-25-2014, 01:47 PM

RE: Philco 38-7CS - by Bob Andersen - 07-25-2014, 04:24 PM

RE: Philco 38-7CS - by morzh - 07-25-2014, 05:02 PM

RE: Philco 38-7CS - by Arran - 07-26-2014, 12:06 AM

RE: Philco 38-7CS - by Bob Andersen - 07-27-2014, 03:35 PM

RE: Philco 38-7CS - by gregb - 07-27-2014, 11:13 PM

RE: Philco 38-7CS - by Bob Andersen - 07-27-2014, 11:28 PM

RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 04:16 PM

RE: Philco 38-7CS - by Mondial - 07-28-2014, 04:26 PM

RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 05:18 PM

RE: Philco 38-7CS - by Mondial - 07-28-2014, 05:36 PM

RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 06:51 PM

RE: Philco 38-7CS - by Bob Andersen - 07-28-2014, 10:29 PM

RE: Philco 38-7CS - by Chuck Schwark - 07-29-2014, 10:35 AM

RE: Philco 38-7CS - by morzh - 07-29-2014, 10:37 AM

RE: Philco 38-7CS - by Chuck Schwark - 07-29-2014, 10:42 AM

RE: Philco 38-7CS - by morzh - 07-29-2014, 11:02 AM

RE: Philco 38-7CS - by Warren - 07-29-2014, 01:59 PM

RE: Philco 38-7CS - by gregb - 07-29-2014, 03:16 PM

RE: Philco 38-7CS - by Bob Andersen - 07-29-2014, 03:31 PM

RE: Philco 38-7CS - by Bob Andersen - 08-03-2014, 02:06 PM

RE: Philco 38-7CS - by codefox1 - 08-03-2014, 04:29 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

Who's Online

There are currently 5147 online users. [Complete List]
» 1 Member(s) | 5146 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me